manualshive.com logo in svg

Zontes ZT310T-M, Руководство по обслуживанию

Zontes ZT310T-M - высококачественный мотоцикл, предназначенный для приключений на дорогах. Для того чтобы поддерживать его в отличном состоянии, необходимо изучить Maintenance Manual. Вы можете загрузить это пособие на manualshive.com бесплатно, чтобы всегда быть готовым к новым поездкам.

Поделиться
Скачать
background image

 

 

83

 / 

184

 

 

 

 

Sound, light, and electrical device 

Inspection 

Caution: 

●Before driving, check whether the lights of the whole 

car are normal, including turn signals, tail lights, brake 
lights, headlights, etc. Whether the horn is normal. 
Whether the windshield rises and falls normally. 

1. Check 

For details of the lamps and lanterns of the whole 

vehicle, please refer to the lamps and lanterns 

distribution diagram in the vehicle information of this 

manual. 

 

1. Front brake handle 2. Right handle switch 3. Right 
auxiliary switch 4. Meter 5. Left auxiliary switch 6. Left 
handle switch 7. Rear brake handle 

a. Park the vehicle on a flat ground or a lifting 

platform, lower the main support, and retract the side 
support. 

b. Press the unlock button of the right auxiliary switch 

①

After the vehicle is unlocked and energized, confirm 

that the flameout switch 

④

  is pulled to "   ", pinch the 

front or rear brake handle, and press the start button 

②

 

to start the engine. 

③

Light switch: keep it at the "●" position, check whether 

the front position light, rear position light and license 
plate light are normally on; pull it to "   " to check the 
handle backlight, front light, front position light, rear 
position light, and license plate The lights should all be 
on. 

⑤

ECO button: Press the meter and it should light up 

"E", and press it again to light up "S", and the two 
modes can be switched freely. 

⑥

SEAT: Press to check whether the cushion lock is 

normally opened. 

⑦

FUEL: Press to check whether the fuel tank cover is 

normally opened. 

 

c. The left switch button test. If you need a more 

detailed understanding of each button function, you can 
check the driver's manual. Here is only a brief 
description of how to test whether it is normal. 

①

SET key: Short press SET to enter the main 

menu/confirm selection. Long press to return to the main 
interface. Operate this button when driving a vehicle is 
prohibited. 

②

MOD key:  Select  the next item. Operate this button 

when driving a vehicle is prohibited. 

③

Windshield switch: Press the windshield glass to 

complete from retracting to opening or from opening to 
retracting. 

④

Steering switch: Push it to the right to check whether 

the front right and rear right turn signals are flashing 
normally; press the turn signal to turn off; push it to the 
left to check whether the left front and left rear turn 
signals are normal. 

⑤

Hazard warning lights: Press it down and the 4 turn 

signals will flash, press it again to turn off. It should 
comply with the requirements of traffic laws and should 
not be used in non-emergency situations. 

⑥

Horn: Press the horn to sound once to confirm 

whether the sound is clear and loud. 

⑦

Dimmer switch: Pull it to " " to check whether the 

high beam light is on, and the high beam indicator 
symbol on the meter lights up at the same time. Pull to "

" to check whether the low beam light is on. The far 

and low beams should be used reasonably in 
accordance with traffic laws and regulations. 

⑧

Overtaking warning light switch: When pressed in the 

low beam, it will turn on the high beam. 

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZT310T-M

HRC '92-RS125R Owner'S Manual preview
'92-RS125R
Бренд: HRC Страницы: 88
hepco & becker 6504513 01 01 Manual preview
6504513 01 01
Бренд: hepco & becker Страницы: 4
hepco & becker 6609516 01 01 Quick Start Manual preview
6609516 01 01
Бренд: hepco & becker Страницы: 4
Fantic Motor XXF 250 User Manual preview
XXF 250
Бренд: Fantic Motor Страницы: 145
Dennis Kirk Scorpion Exo-T520 Tech Manual preview
Scorpion Exo-T520
Бренд: Dennis Kirk Страницы: 10
paladin P4009 Installation And Owner'S Manual preview
P4009
Бренд: paladin Страницы: 2
Evotech Performance KAWASAKI ZX6R 2007/8 Installation Instructions preview
KAWASAKI ZX6R 2007/8
Бренд: Evotech Performance Страницы: 2
Yamaha YZFR1Y(C) Owner'S Manual preview
YZFR1Y(C)
Бренд: Yamaha Страницы: 122
Yamaha YZF R1 2020 Owner'S Manual preview
YZF R1 2020
Бренд: Yamaha Страницы: 142
Yamaha YZFR6W Owner'S Manual preview
YZFR6W
Бренд: Yamaha Страницы: 118
Honda ADV150A User Manual preview
ADV150A
Бренд: Honda Страницы: 4
hepco & becker 6303544 00 01 Quick Start Manual preview
6303544 00 01
Бренд: hepco & becker Страницы: 3
hepco & becker 6304554 00 01 Quick Start Manual preview
6304554 00 01
Бренд: hepco & becker Страницы: 4
SUOMY MX SPEED Manual preview
MX SPEED
Бренд: SUOMY Страницы: 26
Caberg XTRACE Manual preview
XTRACE
Бренд: Caberg Страницы: 16
hepco & becker 5049529 00 01 Quick Start Manual preview
5049529 00 01
Бренд: hepco & becker Страницы: 4
Hama 00201514 Operating Instructions Manual preview
00201514
Бренд: Hama Страницы: 22
hepco & becker 5012527 00 01 Manual preview
5012527 00 01
Бренд: hepco & becker Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды