manualshive.com logo in svg

Zontes ZT310T-M, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT310T-M Скачать руководство пользователя страница 168

 

 

168

 / 

184

 

 

pay attention to each non-standard bolt The bolts 
marked M6×16 are equipped with bushings (2) and 
cushioning glue (3); use 4# inner hexagon to install one 
M6×16 bolt (1) under the decorative cover of the right 
pedal and connected to the surrounding bottom. Note 
that the bolts need to be equipped with bushing 

⑵

, 

cushion rubber 

⑶

; finally buckle in 3 expansion nails 

(green circle). 

 

d. Buckle the rear right pedal rubber pad and the rear 

right pedal rubber pad pressure plate together to the 
right pedal; then buckle the front right pedal rubber pad 
and the front right pedal rubber pad pressure plate 
together to the front storage box panel; check the right 
pedal and Whether the assembly gap between the 
decorative cover of the right pedal and the surrounding 
parts is too large, if it is too large, it is indicated that the 
buckle has not been buckled in place and needs to be 
reinstalled. 

 

e. Use the same method to install the left pedal and 

the left pedal decorative cover. 

 

6.3 Install the rear skirt 

a. Grasp the tail of the right tail skirt (green mark) with 

one hand, and buckle the tail buckle (green mark) into 
the bottom of the tail skirt; align the buckle on the lower 
part of the tail skirt (orange mark) on the front of the rear 
mud board Click the right part of the fuel tank cover 
(gold) with one hand, and buckle the upper part of the 
tail skirt (dark blue mark) into the middle cover of the 
fuel tank (light blue); put the right part of the fuel tank 
cover (gold) ) The rear buckle (purple mark) is buckled 
into the front of the tail skirt; check the assembly gap 
between the right tail skirt and the surrounding parts, 
and reinstall it if there is a large seam. 

 

b. Use 4# inner hexagon to install 2 non-standard 

M6×16 bolts 

⑷

  to the front of the right tail skirt, pay 

attention to the bolts with bushing 

⑵

, cushioning rubber 

⑶

; then put the 2 expansion nails back to the right tail 

skirt The lower part (the green mark). 

 

c. Put back the 2 expansion nails (green mark) on the 

inner and tail of the right tail skirt. Finally, check again to 
check whether the assembly gap between the right tail 
skirt and the surrounding parts is too large or 
interference, if the assembly gap is too large or 
interference, re-assembly is required. 

 

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды