manualshive.com logo in svg

Zontes ZT310T-M, Руководство по обслуживанию

Поделиться
Скачать
Zontes ZT310T-M Скачать руководство пользователя страница 167

 

 

167

 / 

184

 

 

 

e. Install the rear pedal on the right side of the vehicle 

to a suitable position, install two M8×25 bolts 

⑺

, and 

tighten them with a 14# sleeve; connect the small water 
tank inlet pipe to the corresponding pipeline, and tighten 
it with a single batch Clamp; then connect the engine 
water inlet pipe back to the corresponding pipe, and use 
the water clamp clamp to fix the clamp to the 
appropriate position to prevent leakage of coolant. 

 

f. Reconnect the plugs of the stepper motor and the 

three-in-one sensor on the throttle valve body; reconnect 
the connectors of the high-pressure fuel pipe, fuel 
injector, oxygen sensor, crankshaft position sensor, 
magneto stator charging cable, and cylinder head water 
temperature sensor; Reconnect the negative and 
positive wires connected to the starter motor and tighten 
the bolts; install the two tubes that connect the carbon 
canister to the throttle valve body and the oil-air 
separator to the air filter. 

g. Refer to "Adding Coolant to the Main Water Tank" 

to add an appropriate amount of coolant. 

6. The installation of the 

corresponding cover 

6.1 Install the surrounding floor 

a. Grasp the rear part (green mark) surrounding the 

bottom (glossy yellow) with one hand, and hold the 
middle part (purple mark) surrounding the bottom with 
one hand, and install the surround forward (big arrow), 
and the groove at the bottom must be surrounded 
Clamp into the frame and fix it; when the two grooves 
are clamped into the frame, shoot the front part of the 
surrounding bottom plate up (small arrow) until the front 

part of the surrounding bottom plate is locked into the 
shock-absorbing sleeve of the small water tank. 

 

6.2 Install pedal and pedal decorative cover 

a. Push the right decorative cover (blue) of the front 

storage box panel out with one hand, and install the right 
pedal and the right pedal decorative cover (gold) into the 
appropriate position with the other hand; after installing it 
in place, use the 5# inner hexagon to move the front 
storage box Tighten a non-standard M6×16 bolt under 
the right decorative cover (blue) of the panel ( (Purple 
mark) press down, click into the corresponding position, 
and then click the buckle under the decorative cover of 
the right pedal (green mark) into the corresponding 
position. 

 

b. Fasten the buckle on the front of the right pedal 

decoration cover (the blue mark) into the corresponding 
position, and then use the 4# inner hexagon to install the 
right pedal decoration cover (gold) to connect the two 
M6×16 bolts 

⑴

  surrounding the middle part, Pay 

attention to the bolt belt traversing the bushing 

⑵

, 

cushioning glue 

⑶

. 

 

c. Use 4# inner hexagon to install 2 M6×12 bolts on 

the front storage panel 

⑸

; use 5# inner hexagon to 

install 4 non-standard M6×16 bolts on the right pedal 

⑷

, 

Содержание ZT310T-M

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды