Zontes ZT310T-M Скачать руководство пользователя страница 161

Страница: 161 / 184

161

184

c. Put the rubber pad

⒀

on the direction column

adjustment nut; then screw in the second direction
column adjustment nut

⑿

, screw the second direction

column adjustment nut

⑿

to align with the notch of the

first direction column adjustment nut

⑿

, put Insert the

snap-in gasket

⒁

; finally screw in the third steering

column adjusting nut

⑿

, torque: 100N.m (10.2 kgf.m, 74

bf.ft)

d. Install the semi-circular key in the groove of the lower

link plate, then align the gap between the spacer and the
base

⒃

with the semi-circular key

⒂

, and finally screw

in the cap nut

⒄

, torque: 100N.m (10.2 kgf.m, 74 bf.ft)

6. Install other disassembly components

a. Refer to "Replace the front shock absorber" to

replace the front shock absorber.

b. Refer to "Replace the front wheel" to reinstall the

front wheel assembly.

c. Refer to "Replace the direction handle" to install the

assembly back in the direction.

●The vehicle must be parked on a level and stable

ground or on a lifting platform.

Содержание ZT310T-M

























































































































































































Результаты поиска

Содержание ZT310T-M

Отзывы:

Бренды по названию

Популярные бренды

Zontes ZT310T-M, Руководство по обслуживанию

Результаты поиска

Содержание ZT310T-M

Отзывы:

Бренды по названию

Популярные бренды