background image

1

© Copyright 2018 Zoeller

®

 Co. All rights reserved.

SECTION:Z4.30.075

ZM2606

Rev. A 

0218

Supersedes

1017

NOTICE TO INSTALLER:  Instructions must remain with installation.

Part Number:

 ______________ 

 Date Code:

 _______________

  Simplex    

 

Duplex 

  Packaged System 

  Field Assembled System 

Job Name: ____________________________________________
Distributor:

 ____________________________________________

Date of Purchase:

 _________

  Zoeller S/O No.:

 ______________

Contractor:

 ____________________________________________

Date of Installation:

 ____________________________________

System Readings During Start-up:   Voltage

 _____

 Amps 

______

 

Owner’s Information

Safety Instructions

TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR MAJOR 

PROPERTY DAMAGE, READ AND FOLLOW ALL SAFETY  

INSTRUCTIONS IN THIS MANUAL AND ON THE PUMP.

THIS MANUAL IS INTENDED TO ASSIST IN THE INSTALLATION 

AND OPERATION OF THIS UNIT AND MUST BE KEPT WITH 

THE PUMP.

This is a 

SAFETY ALERT SYMBOL.

When you see this symbol on the pump or in the 

manual, look for one of the following signal words 

and be alert to the potential for personal injury or 

property damage.

Warns of hazards that 

WILL

 cause serious personal    

injury, death or major property damage.

Warns of hazards that 

CAN 

cause serious personal 

injury, death or major property damage.

Warns of hazards that 

CAN 

cause personal injury 

or property damage.

INDICATES SPECIAL INSTRUCTIONS WHICH ARE 

VERY IMPORTANT AND MUST BE FOLLOWED.

THOROUGHLY REVIEW ALL INSTRUCTIONS AND WARNINGS 

PRIOR TO PERFORMING ANY WORK ON THIS PUMP.

MAINTAIN ALL SAFETY DECALS.

PUMPS WITH THE “UL” MARK AND PUMPS WITH THE “US” 

MARK ARE TESTED TO UL STANDARD UL778. CSA CERTIFIED 

PUMPS ARE CERTIFIED TO CSA STANDARD C22.2 NO. 108.

CAUTION

Table of Contents

Safety Instructions .......................................................................1
Limited Warranty and Application ..............................................2
Preinstallation Checklist ..............................................................3
General Information .....................................................................4
Pump Wiring Instructions ............................................................5
Typical Indoor Prepackaged System ..........................................6
Indoor Prepackaged Installation Instructions ...........................7
Typical Outdoor Prepackaged System .......................................8
Outdoor Prepackaged Installation Instructions ........................9
Operation .....................................................................................10
Cutter Maintenance .................................................................... 11
Service Checklist ........................................................................12

REFER TO WARRANTY ON PAGE 2.

 

This manual incorporates the installation, operation, maintenance, and 

service instructions into one document to aid in the ownership of a Zoeller 
submersible wastewater product.  Please read and review this manual before 
installing the product.  Follow the steps and procedures listed on ZM1074 for 
a proper start-up and warranty protection. Many items contained within, when 
followed correctly, will not only ensure a long and problem-free life for the pump, 
but also save time and money during installation.  Should further assistance be 
necessary please call our Technical Service Department at 1-800-928-7867.

 

Congratulations on the purchase of a Zoeller submersible grinder pump.  

This pump has been constructed in compliance with FM and CSA testing. 
These requirements enable the unit to be listed as an explosion proof 
pump rated for use in Class I, Division 1, Group C & D locations.  

For over 

seventy years the name Zoeller has represented the standard for submersible 
dewatering and sewage pumps.  The same high quality workmanship and 
easy maintenance design has been incorporated into this line of heavy-duty 
submersible grinder pumps.  This Zoeller pump will provide years of trouble-free 
service when installed according to the manufacturer’s recommendations.

OWNER’S MANUAL

X70 HAZARDOUS LOCATION SERIES CLASS I,

DIVISION 1, GROUP C & D SUBMERSIBLE GRINDER UNITS

Certified to CSA Standard

C22.2 No. 145

Standard 3600 

& 3615

MAIL TO:  P.O. BOX 16347 • Louisville, KY  40256-0347

SHIP TO:  3649 Cane Run Road • Louisville, KY  40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624

visit our web site:

zoellerengprod.com

Product information presented 

here reflects conditions at time 

of  publication. Consult factory 

regarding discrepancies or 

inconsistencies.

Register your 

Zoeller Engineered Product 

on our website:

http://reg.zoellerengprod.com/

Содержание X70 Series













Отзывы: