background image

 FM2537

0415

Supersedes

0513

OWNER’S MANUAL

Potable Water Convertible Jet Pumps

Safety Instructions

CAUTION

  This manual incorporates the installation, operation, maintenance, 

and service instructions into one document to aid in the ownership of 

a Zoeller potable water product. Please read and review this manual 

before installing the product. Many items contained within, when 

followed correctly, will not only ensure a long and problem-free life 

for the system, but also save time and money during installation. 

Should further assistance be necessary please call our Technical 

Service department at 1-800-928-PUMP.

© Copyright 2015 Zoeller

®

 Co. All rights reserved.

P/N  023072

TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR MAJOR 

PROPERTY  DAMAGE,  READ  AND  FOLLOW  ALL  SAFETY      

INSTRUCTIONS IN MANUAL AND ON PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE INSTALLATION 

AND OPERATION OF THIS UNIT AND MUST BE KEPT WITH 

THE PUMP.

This is a SAFETY ALERT SYMBOL.

When you see this symbol on the pump or in the 

manual, look for one of the following signal words 

and be alert to the potential for personal injury or 

property damage.

Warns of hazards that WILL cause serious personal    

injury, death or major property damage.
Warns of hazards that CAN cause serious personal 

injury, death or major property damage.
Warns of hazards that CAN cause personal injury 

or property damage.
Indicates special instructions which are very 

important and must be followed.

THOROUGHLY REVIEW ALL INSTRUCTIONS AND WARNINGS 

PRIOR TO PERFORMING ANY WORK ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.

Table of Contents

Safety Instructions ..........................................................................1
Limited Warranty.............................................................................2
Preinstallation Information ...........................................................2-3
Installation Procedures  ...............................................................4-7
Parts List .........................................................................................7
Troubleshooting Checklist ..............................................................8

  Congratulations on the purchase of the Zoeller Potable Water 

Convertible Jet Pump. Since 1939  the name Zoeller has represented 

the standard for submersible sump and sewage pumps. The 

same high-quality workmanship and easy maintenance design 

has been incorporated into this line of potable water products. 

This Zoeller system will provide years of trouble-free service 

when installed according to the manufacturer recommendations.

Owner’s Information

Model Number: ______________________  Date Code:   _________________

Job Name:  ______________________________________________________ 

Dealer:   _________________________________________________________

Date of Purchase:  _______________________________________________

Contractor: _____________________________________________________

Date of Installation:  _______________________________________________

System Readings During Operation:  Voltage __________ Amps  _________

SEND TERESA BOWSMAN @  F&W A PDF WHEN THIS FILE IS CHANGED.

Product information presented 

here reflects conditions at time 

of  publication. Consult factory 

regarding discrepancies or 

inconsistencies.

MAIL TO:  P.O. BOX 16347 • Louisville, KY  40256-0347

SHIP TO:  3649 Cane Run Road  • Louisville, KY  40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624

visit our web site:

www.zoeller.com

®

Your Peace of Mind is Our Top Priority

 

®

Register your 

Zoeller Pump Company 

Product on our website:

http://reg.zoellerpumps.com/

Содержание 023072

















Отзывы: