Page 33
ENGLISH
Installation and Operation Manual
|
Jandy
®
LXi
™
Model Pool and Spa Heater by Zodiac
®
NOTE
The display will revert back to
OFF
after one
minute since the last key press.
3. To select a language, use the
Up
or
Down
but-
ton to display
SELECT USER SETUP LAN-
GUAGE
. Press the
MENU
button. The
SELECT
LANGUAGE ENGLISH
(default language)
appears, use the
Up
or
Down
button to scroll
through the language options. When you reach
the desired language, press the
MENU
button to
select the language. Press
POOL
or
SPA
to exit
the User Setup mode.
7.4.2 Temperature Scale Setup
1. Make sure the control is in the
OFF
mode.
2. To enter the User Setup mode, press and hold the
MENU
button for 5 seconds.
3. To select temperature scale, use the
Up
or
Down
button to scroll through to display
SELECT
USER SETUP TEMPERATURE SCALE
. Press
the
MENU
button. The
SELECT TEMP SCALE
°F:
(default temperature scale) appears, use the
Up
or
Down
button to scroll to display
SELECT
TEMP SCALE °C:
.
When you reach the desired
temp scale, press the
MENU
button to select.
Press
POOL
or
SPA
to exit the User Setup mode.
7.4.3 Spa Timer Setup
1. Make sure the control is in the
OFF
mode.
2. To enter the User Setup mode, press and hold the
MENU
button for 5 seconds.
3. To select spa timer, use the
Up
or
Down
but-
ton to scroll through to display
SELECT USER
SETUP SPA TIMER
.
Press the
MENU
button.
The
SELECT SPA TIMER CONTINUOUS:
(de-
fault spa timer setting)
is displayed. To turn the
spa on or off indefinitely, press the
MENU
button
to select.
4. To select the length of time for the spa to run, use
the
Up
or
Down
button to scroll to display
SE-
LECT SPA TIMER TIME SELECTION
.
Press
the
MENU
button to select.
The display
SELECT
SPA TIME 01:00 HRS:
(default time setting) is
displayed. Use the
Up
or
Down
button to select
the length of time for the spa to run (between
00:15 to 23:00 hours in increments of 00:15 min-
utes). Press the
MENU
button to select how long
the spa will run. Press
POOL
or
SPA
to exit the
User Setup mode.
7.4.4 Display Light Setup
1. Make sure the control is in the
OFF
mode.
2. To enter the User Setup mode, press and hold the
MENU
button for 5 seconds.
3. To select display light setup, use the
Up
or
Down
button to scroll through to display
SELECT
USER SETUP DISPLAY LIGHT
. Press the
MENU
button. The
SELECT DISPLAY LIGHT 2
MIN TIMEOUT:
(default display light setting)
is
displayed. This option allows the display light to
turn off after 2 minutes. Press the
MENU
button
to select. Use the
Up
or
Down
button to scroll
to display
SELECT DISPLAY LIGHT LIGHT
OFF:
, this option allows the display light to turn
off, press the
MENU
button to select. Use the
Up
or
Down
button to scroll to display
SELECT
DISPLAY LIGHT LIGHT ON:
,
this option al-
lows the display light to turn on, press the
MENU
button to select. Press
POOL
or
SPA
to exit the
User Setup mode.
7.5
Set Point Lockout
Make sure the control is in the
ON
mode (
POOL
or
SPA
), press and hold the
Up
and
Down
buttons for
5 seconds. The set point will be locked and the control
will operate in the mode it was in when the Set Point
Lockout occurred. If an attempt to change the set point
is made while the control is in Set Point Lockout,
the control will display
SET POINT LOCKED
. To
unlock the Set Point Lockout, press and hold the
Up
and
Down
buttons for 5 seconds. The unit will display
SET POINT UNLOCKED
.
7.6
Lighting and Shutdown Procedures
WARNING
Do not attempt to light the heater with the door off.
Doing so may cause severe bodily injury.
AVERTISSEMENT
Ne tentez pas d’allumer l’appareil sans que la porte
soit en place. Vous pourriez être victime de bles-
sures corporelles graves.
Before starting your heater, be sure that all of
the functions and limits of the LXi controller has been
set according to the previous sections of this manual.
Once the control is set to your preferences, follow the
instructions outlined below. Read and follow all safety
instructions first. A more detailed set of lighting and
shutdown instructions are listed on the label located on
the inside of the heater door and in Figure 31.