3.
Installation
Please pay attention to the following items. Mis-operation may lead to
personal injury.
equipment failure even the
1)
Do not power on the system before the installation is completed. Do not carry on the install or repair operation at power on state.
2)
All external devices must be grounded.
3)
It is recommended that all wires should run through PVC or galvanized pipes.
5)
It is recommended that the card reader and exit button should be installed at height about 1.4-1.5m.
4
We recommend that the exposed part of all wires should be shorter than 4 mm, t
)
o avoid short circuit or communication failure
6)
It is recommended to use the separated power supply for the control panel and the lock.
2.
Components
1.
Cautions
4.
LED Indicators and Wire Illustration
C3
-4 60
Installation and Connection Guide
Version
:1 . 0
Date: Mar. 2011
caused by unexpected contact of exposed wires.
Notes
:
1) Meaning of LED indicators
:
LINK
indicator (green): Light always indicates TCP/IP
communication
ACT
indicator (yellow): Flash state indicates the data is in transmitting
EXT RS485
indicator (yellow&green): Flash state indicates it is sending
PC RS485
indicator (yellow&green): Flash state indicates it is sending
POWER
indicator (red):
Light always indicates the control panel is
RUN
indicator (green): Flash state indicates the system works normally.
CARD
indicator (yellow): Flash state indicates card is punched on reader.
A. Use 2-conducotor power cord.
2) Recommended use of wires
：
3) The auxiliary input may be connected to infrared body detectors,
4
The auxiliary output may be connected to door bells, alarms, etc.
)
5) State Indicator is connected to the panel box, that is power indicator,
B. Use 6-conductor wire between Wiegand reader and control panel
C. Use 4-conducotor lock power cord (RVV 4*0.75mm)
D. Use 2-conducotor switch power cord
(
RVV
2*0.5
mm)
is proper;
power on.
alarm switches, etc.
through TCP/IP communication.
or receiving data through RS485 communication.
or receiving data through RS485 communication.
(RVVP 6*0.5mm) (To choose the proper cord according to the
interface you connect, such as 6, 8, 10 cord.)
Ethernet interface
Dip switch
PC RS485 interface
Auxiliary output1
Auxiliary output
3
Auxiliary output2
Auxiliary output
4
#1 Door
#3 Door
#2 Door
#4 Door
Lock Power
Power of Control Panel
A
A
C
C
C
C
D
D
D
D
D
D
D
D
D
D
D
D
B
B
B
B
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
Exit Button
Exit Button
Exit Button
Exit Button
State Indicator
EXT RS485
Auxiliary Input1
Auxiliary Input3
Auxiliary Input2
Auxiliary Input4
Wiegand reader
Wiegand reader
Wiegand reader
Wiegand reader
LINK
ACT
run status indicator and communication status indicator.
#1 Door
#1 Door
#2 Door
#3 Door
#4 Door
#2 Door
#3 Door
#4 Door
S
T
A
T
E
PWR
E
X
T
R
S
4
8
5
P
C
R
S
4
8
5
S
W
IT
C
H
Description of normal working state:
Box Lock Hole
State Indicator
Thread Hole
Backup Battery
Control Panel
Air Switch
Power on the system . In normal working state, the power (red) and run indicator (yellow) is on constantly, and the communication
Appearance of Panel Box
Internal of Panel Box
Get the Panel off the track
Heat
Thread holes
Screws
Power
Supply
Temper
Switch
After the following installation, fix the panel on the track first, and then install other
components to original
positions.
indicator (green) flashes.
Dissipation Hole
Control
Panel
Control
Panel
Panel
Track
Panel
Track
2
2
1
1
3) Install
other
components
2) Fix the box
1) Get through the thread hole
