Key hole
Thread hole
Thread hole
3.
Get through the thread hole
Get through the thread hole
Fixed case
1
2
4.
LED indicators, Wires, Auxiliary Input and Output
Appearance of case
Notes
:
C3
-100
Installation Instructions and Connection Guide
1.
Cautions
Please note the following cautions.Mis-operation may lead to personal injury or equipment failure:
1）
Do not energize the system before installation is complete; never carry out installation activities when
Vision
:1. 0 .1
Date
:
Oct. 2010
2）
All peripheral devices must be grounded.
3）
It is preferred that all wires run through PVC or galvanized pipes.
5）
It is recommended that card readers and buttons should be installed at height of 1.4m-1.5m above ground.
6）
It is recommended to use the power supply in case for control panel, and external power supply for each
4）
It is strongly recommended that the length of exposed part of any connection cable should not be longer
Professional clamping tools may be used to avoid unintentional contact of exposed wires to
than 4 mm.
the system is energized.
short-circuit or communication failure.
avoid
Description of normal working state:
Connect the system to the power supply.If the system works properly,the POWER indicator(red) is lit
constantly and the RUN indicator(green) flashes.
Heat
dissipation
hole
2.
Components
Power supply
Backup battery
Control panel
1)Meaning of LED indicators
:
LINK
indicator(green): always(green) indicates TCP/IP
ACT
indicator(yellow):its flashing indicates data is in transmitting
TX
indicator(yellow):its flashing indicates it is sending data through
RX
indicator(green):its flashing indicates it is receiving data through
Auxiliary output
indicator(green):always(green) indicates it is in use.
Lock
indicator(green):always(green) indicates lock is open.
POWER
indicator(red):
a
lways(red) indicates control panel is power
RUN
indicator(green):its flashing indicates the system works normally.
CARD
indicator(yellow):its flashing indicates card is punched on reader.
A Use 2-conducotor power cord
2)
Recommended use of wires
：
3)
The auxiliary input may be connnected to infrared body detectors,
4)
The auxiliary output may be connected to door bells,alarms,etc.
B
Use 6-conductor wire between wiegand reader and control panal
C Use 4-conducotor lock power cord (RVV 4*0.75mm)
D
Use 2-conducotor switch power cord
（
RVV
2*0.5
mm
)
communication is proper;
on.
alam switches,etc.
Ethernet interface
Dip switch
RS
485
interface
Auxiliary output1
Door
1
Power of lock
Power of control panel
A
A
C
D
D
B
B
{
{
{
{
{
B
U
T
T
O
N
1
R
E
A
D
E
R
1
R
E
A
D
E
R
2
+12
V
+12
V
GND
GND
WD
1
WD
1
WD
0
WD
0
GLED
GLED
BEEP
BEEP
IN
GND
ACT
LINK
1
TX
RX
V
+
P
O
W
E
R
P
C
NC
COM
NO
COM
NO
NC
L
O
C
K
1
GND
SEN
V
-
GND
485-
485+
A
U
X
O
U
T
1
L
O
C
K
GND
+12
V
1
2
3
4
O
N
5
6
7
8
1
POWER
CARD
RUN
L
A
N
SD card
Advanced Access Control
lock.
through TCP/IP communication.
RS485 communication.
RS485 communication.
(RVVP 6*0.5mm) (To choose the proper cord according to the
interface you connect, such as 6,8,10 cord.)
1# Door Button
1# Door
wiegand reader
1# Door
wiegand reader
