ZIV SW3 Скачать руководство пользователя страница 45

Страница: 45 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

45/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

FIGURE 24

Example for using the

Overlapping Enable

parameter

4 VLANs with common ports and UNTAGGED clients = OVERLAPPING ENABLE ACTIVATED

VLANs:

The individual configuration parameters for each VLAN are:

•

Indicates the position in the table.

•

Name.

A mnemonic descriptive field available to users.

•

VID.

It sets the VLAN identifier. Valid values are

4095

•

PRI Override.

This sets whether the priority of the frames received in the ports

assigned to the VLAN VID should be overridden in the PRI field value (enabled

option), or whether it should be maintained (Disabled option). This field does

NOT

affect the ports in which the VLAN function parameter is configured as trunk.

•

PRI.

If the

PRI Override

option is enabled, the original priority of the frames received

with a

tag

will be modified with the selected value.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 45 / 122

Результаты поиска

Содержание SW3

Отзывы: