Zinc BMX-Vital Скачать руководство пользователя

Страница: 4 / 22

Customer Helpline

01582 670100

While assembling the bike, it is recommended that, where possible, a torque spanner is used to
tighten nuts and bolts. The table below provides a list of torque settings for the various nuts and bolts.

Recommended Tightening Information

Front Wheel Nuts

Rear Wheel Nuts

Seat Binding Nut

Seat Pillar Clamp Nut

Brake Anchor Nut

Handle Bar Clamp Nut

Head Stem Expander Bolt

Crank Cotter Pin Nuts

Brake Centre Bolt

Pedals

22 - 27 Newton Metres

24 - 29 Newton Metres

12 - 17 Newton Metres

4 - 19 Newton Metres

7 - 11 Newton Metres

5 - 19 Newton Metres

17 - 19 Newton Metres

5 - 10 Newton Metres

5 - 7 Newton Metres

35 - 40 Newton Metres

Important - Please read instructions fully before starting assembly

CAUTION!

Only use suitable tools to assemble the bike. The use of unsuitable tools may lead to

personal injury and damage to the bike.

CAUTION!

Always ensure all packaging is removed from the bike before assembly and use. Failure to

remove the packaging may prevent the correct operation and may lead to personal injury and damage
to the bike.

CAUTION!

The safety and smooth running of the bike can only be preserved with regular

maintenance. Always ensure the bike is maintained in accordance with the supplied maintenance
manual.

CAUTION!

Before attaching the handlebar assembly, make sure all the cables are free to move

and are not tangled. Failure to observe this caution may prevent correct operation and may lead to
personal injury and damage to the bike.

IMPORTANT!

Before assembling the bike, check all the parts indicated in the manual are in the

box. Inspect the parts for signs of damage. Do not assemble the bike if you observe any damaged
components.

IMPORTANT!

Always take care when removing the packaging to prevent damage to the bike.

NOTE!

Always recycle the packaging in accordance with local recycling schemes.

NOTE!

The pedals and crank arms have colour coded stickers to indicate which pedal matches which

Crank Arm.

NOTE!

The threads on the left and right pedals are different. To prevent damage to the threads, only

tighten the pedals in the direction indicated on the stickers.

NOTE

Safety Information

Содержание BMX-Vital























Результаты поиска

Содержание BMX-Vital

Отзывы:

Похожие инструкции для BMX-Vital

Бренды по названию

Популярные бренды

Zinc BMX-Vital, Инструкция по эксплуатации

Результаты поиска

Содержание BMX-Vital

Отзывы:

Похожие инструкции для BMX-Vital

Бренды по названию

Популярные бренды