Zimmer DES Series Скачать руководство пользователя страница 39

Страница: 39 / 54

11.4 TIA Portal

NOTICE

This section uses the commissioning of the product of the DES190 installation size as an example project. This

example project can be transferred to the DES140 installation size.
The example project is intended as an aid and must not be used as a programming template.

Commissioning the product depends on the configuration of the drive control unit and can therefore vary.

11.4.1

Configuring the drive control unit

►

Connect the drive control unit to the computer using its network interface.

►

Search for the correct drive control unit using the

IndraWorks Ds

software, see section “Setting the IP address”.

The connection to the drive control unit is established.

►

In the

Configuration

menu, click

Load

The

Load Parameters

window opens.

►

Enable the option field of the desired parameter set.

►

Click the

Load

button.

The

Load Parameters

window closes.

►

In the navigation pane, click

Master

Communication

The

Master Communication Basic Settings

tab is displayed in the window.

►

In the

Active Protocol

drop-down menu,

select the communication type for the

control system.

►

Click the

Engineering via IP (X24/X25)

tab.

►

Enter the IP address for configuring the drive control unit.

INSTALLATION AND OPERATING INSTRUCTIONS:

DES

DDOC00192 / f

EN / 2022-07-20

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

Содержание DES Series























































Результаты поиска

Содержание DES Series

Отзывы:

Похожие инструкции для DES Series

Бренды по названию

Популярные бренды

Zimmer DES Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DES Series

Отзывы:

Похожие инструкции для DES Series

Бренды по названию

Популярные бренды