Zhone IMACS 8000, Руководство пользователя

Страница: 304 / 788

9-4 System Cards
Model No.
Running Head
WAN Card Descriptions WAN Card
Table 9-1. 801070 WAN Strap Setting Options
9.2.1.2 WAN Software Level
The version of the software contined in the WAN card is able to be determined by the
craftsperson. At the time of introduction, the load on the WAN is version 1.0.2. The
craftsperson can determine this information by looking at the serialization of the card. To do
so, login into the IMACS shelf, and position the cursor on the 801070 or 801470. Execute the
sEr command by hitting the “E” from the keybord. A display will pop-up as in Figure 9-3, and
the area identified shows that this WAN is running version 1.0.2 of the software.
Starting in the 6.1.1 release is the ability to poll the systems using SNMP to retrieve the same
information. This enhancement provides the customer the ability to remotely poll the IMACS
systems to retrieve the WAN software level in the entire network. This change is in the IMACS
software only; no new MIBs are required. The interface to the IMACs to retrieve this
information is in the standard MIB definitions, specifically in the OID found at:
.iso.org.dod.internet.mgmt.mib-2.interfaces.ifTable.ifEntry.ifDescr or OID
.1.3.6.1.2.1.2.2.1.2.
Following is an example of the data returned when the customer issues the MIB command:
6001 : WAN8010; DSX+DSX; Rev E3-000 Ser 18791 FWRel 000000; s:w1; u:1; State: act
6002 : WAN8010; DSX+DSX; Rev E3-000 Ser 18791 FWRel 000000; s:w1; u:2; State: act
7001 : WAN8010; CEPT+CEPT; Rev F0-000 Ser 00858 FWRel 000000; s:w2; u:1; State: act
7002 : WAN8010; CEPT+CEPT; Rev F0-000 Ser 00858 FWRel 000000; s:w2; u:2; State: act
8001 : WAN8010; DSX+DSX; Rev E3-000 Ser 16975 FWRel 000000; s:w3; u:1; State: stby
8002 : WAN8010; DSX+DSX; Rev E3-000 Ser 16975 FWRel 000000; s:w3; u:2; State: act
9001 : WAN8014; DSX+DSX; Rev A3-000 Ser 00005 FWRel 010009; s:w4; u:1; State: stby
9002 : WAN8014; DSX+DSX; Rev A3-000 Ser 00005 FWRel 010009; s:w4; u:2; State: stby
Note that the standard WAN cards display FWRel of 000000, whereas the new WAN cards
display values other then 000000. The data returned by this query is in hex, so that decimal
ten will display 000A, eleven will be 000B, and so on. In the example above, the WAN card
in slot w4 returned the value of 010009, indicating that this card is running the 01.00.09 WAN
WAN Interface Type P1 J10 J12 J13 P2 J11 J14 J15
T1 DSX Mode 1-2
None or
between 2 and 3
1-2
None or
between 2 and 3
T1 CSU Mode None None None None
E1 with 75 Ohm
Termination
Impedance
3-4 1-2 3-4 1-2
E1 with 120 Ohm
Termination
Impedance
3-4 2-3 3-4 2-3