ZF CruiseCommand 785CE Скачать руководство пользователя страница 16

Страница: 16 / 160

OPERATION

Page 8

2.9 O

EVER

PERATION

ODE

ULTI

CREW

)

This System utilizes One Lever Operation Mode to allow one Control

Head lever (Master) to command all engines and gears. The "Master"
lever can be any lever. The advantage of this is that only one Control
Head lever operates all engines and gears. Normal control sequenc-
ing and timing applies to all engines.

To turn OFF One Lever Operation:

A)Place the Master Control Head lever into the Neutral Detent.
B) Place the in-active Control Head lever(s) into the Neutral

Detent.

C) The green LED will turn Off, indicating control system is now

in Normal Operating Mode.

NOTE: The green LED will always be lit while in One Lever Operation, no matter what position

the Master Control Head lever is in.

NOTE: The Control Head lever(s) that are in-active can now be placed out of the way in any posi-

tion forward of the Ahead detent.

Figure 7: Step A One Lever Operation Mode

One Lever Operation Mode must be
enabled.

To turn ON One Lever Operation:

A)At the Station-in-Command,

move all of the Control Head
levers to the Ahead Detent

Figure 8: Step B One Lever Operation Mode

B) Push and Hold the transfer but-

ton while moving the Master
Control Head lever out of the
Ahead detent.

DO NOT

RELEASE TRANSFER BUT-
TON

until the green light turns

On, indicating One Lever Oper-
ation Mode is now Active.

CAUTION: It is strongly recommended that the Master Lever is returned to the Neutral/Idle posi-

tion prior to disabling One Lever Operation. Failure to do so may result in a sudden
change in vessel direction.

NOTE: One Lever Operation may be used in Troll Mode or in Non-Troll Mode.

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды