ZF CruiseCommand 785CE Скачать руководство пользователя страница 139

Страница: 139 / 160

Throttle Testing

TRAIN-157 Rev.B 6/01

Page 42

G)Turn power ‘On’ to the CruiseCommand Processor and take com-

mand at any remote station.

H)Record the DC Voltage at this time. The measurement should be 7

- 9% of the voltage recorded in step F). Refer to Figure 36:. If the
DC Voltage is off slightly, it may be adjusted using the Throttle
Minimum "

" Function.

I) Move the Control Head lever to the Full Throttle position while

depressing the Transfer Button (Throttle Only Mode).

J) The measurement should be 91 - 93% of the voltage recorded in

step F). Refer to Figure 37:. If the voltage is off slightly, it may
be adjusted using the Throttle Maximum "

" Function.

K)Return the Control Head lever to the Neutral/ Idle position and

turn power ‘Off’ to the Processor.

L) Remove the Test Unit and plug the Throttle Harness back into the

Processor’s Throttle Socket.

Figure 37: Dwg 11653-H

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды