ZF CruiseCommand 785CE Скачать руководство пользователя страница 134

Страница: 134 / 160

Throttle Testing

TRAIN-157 Rev.B 6/01

Page 37

I) Return the Control Head lever to the Neutral/ Idle position and

turn power ‘Off’ to the Processor.

J) Remove the Test Unit and plug the Throttle Harness back into the

Processor’s Throttle Socket.

2.2 C

URRENT

(

A.)

A)Ensure power is removed from both the Engine Electronics and

the CruiseCommand Processor.

B)Disconnect the Throttle Harness from the Throttle Socket on the

Processor.

C)Insert the Test Unit between the Throttle Socket and the Throttle

Harness as shown in Figure 31:.

D)Set-up a Multi meter to measure mA. and plug the test leads into

the Test Unit as shown in Figure 31:

E) Turn Power ‘On’ to the Processor and take command at any

Remote Station.

Figure 31: Dwg 11653-C

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды