ZF CruiseCommand 785CE Скачать руководство пользователя страница 133

Страница: 133 / 160

Throttle Testing

TRAIN-157 Rev.B 6/01

Page 36

2.1 DC V

OLTAGE

A)Ensure power is removed from both the Engine Electronics and

the CruiseCommand Processor.

B)Disconnect the Throttle Harness from the Throttle Socket on the

Processor.

C)Insert the Test Unit between the Throttle Socket and the Throttle

Harness as shown in Figure 29:, page 35

D)Set-up a Multi meter to measure DC Volts and plug the leads into

the Test Unit.

E) Turn Power ‘On’ to the Processor and take command at any

Remote Station.

F) The appropriate Idle Voltage for the application should be mea-

sured at this time. If the voltage is off slightly, it may be adjusted
using the Throttle Minimum "

" Function.

G)Move the Control Head lever to the Full Throttle position while

depressing the Transfer Button (Throttle Only Mode).

H)The appropriate Full Throttle voltage for the application should be

measured as shown in Figure 30:. If the voltage is off slightly, it
may be adjusted using the Throttle Maximum "

" Function.

Figure 30: Dwg 11653-B

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды