ZF CruiseCommand 785CE Скачать руководство пользователя страница 109

Страница: 109 / 160

TROUBLESHOOTING

TRAIN-156 Rev.B 11/01

Page 13

cates a closure (depressed Transfer Button) of the switch,
while a “

” indicates an open switch. This will also be cov-

ered in more detail later.

F) Depressing the Up or Down Arrow one more time will show the

current revision level of the software. This feature will provide
invaluable information in the years to come. Determining the
characteristics or capabilities of a certain CruiseCommand will be
as simple as selecting this feature.

G)Pressing the Up or Down Arrow (Scroll) Push-button once more,

returns you to the Applied Battery Voltage.

H)The Diagnostic Menu can be exited two ways:

• Do not touch any Push-buttons for 1 minute. The system will

automatically exit.

• Depress the Left Arrow Push-button until

“H0 00”

appears.

You may now scroll through the Set-up Menu.

Figure 11: Display Stations Control Head Transfer Button Status

Figure 12: Display Software Revision Level

Содержание CruiseCommand 785CE

































































































































































Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды

ZF CruiseCommand 785CE, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание CruiseCommand 785CE

Отзывы:

Похожие инструкции для CruiseCommand 785CE

Бренды по названию

Популярные бренды