manualshive.com logo in svg

ZF-DUOPLAN 2K2100, Руководство по эксплуатации

Поделиться
Скачать
ZF-DUOPLAN 2K2100 Скачать руководство пользователя страница 31

Operating Instructions 

2K2100 with STW 

 

Repair 

6.2

 

Gearbox removal 

(based on the example of the version with adapter 
plate and shaft seal) 

Proceed accordingly in the case of other versions.

 

 

•

 

Switch off the machine 

•

 

Switch off the power supply 

•

 

Disconnect the electrical connections 

•

 

Disconnect the gearbox oil connections, drain 
the gearbox oil 

•

 

Undo the mounting bolts (11)  

•

 

Pull the gearbox (6) off the adapter plate (5) 
and drive hub (1) 

 

6.3

 

Hub 

•

 

Undo the threaded pin (9) used to radially 
secure the fitted key 

•

 

Use a removing device, e.g. three-arm puller, 
to pull off the drive hub against the motor shaft 
without heating the hub. 

 

 

Dimension C

 

023718 

 

1

 

Drive hub 

2

 

Motor shaft 

3

 

Motor 

4

 

Adapter plate 

5

 

Gearbox housing 

6

 

Shaft seal 

7

 

Threaded pin 

8

 

O-ring 

9

 

Mounting bolt (gearbox-adapter) 

10

 

Mounting bolt (adapter-motor) 

 

31 

Содержание 2K2100



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды