Zero FX 2018 Скачать руководство пользователя | Manualshive

Страница: 45 / 156

background image

General Operation

4.3

OFF Position

This position is used to turn the motorcycle OFF, disabling
the electrical system.

ON Position

This position is used for operating the motorcycle. In this
position the following sequence occurs:

•

Lights turn ON

•

Dash display turns ON

Motorcycle Tip-Over Sensor

Your motorcycle has a tip-over sensor that will disable the
motorcycle’s drive mode in the event it is activated. If your
motorcycle’s tip-over sensor is activated:

•

The motorcycle drive mode will be disabled while
tipped-over.

•

The motorcycle can’t be driven or charged while in a
tipped-over state.

•

Upright the motorcycle and perform one full key cycle
(turn the key to the OFF position, wait for the display to
go blank and then turn the key back to the ON position)
to reset the sensor.

Note: Altering the factory suspension or changing the
location of the MBB (Main Bike Board) may cause either
detection of a false tip-over state or disable the detection in
the case of an actual tip-over.

Zero Owner's Manual (FX and FXS).book Page 3 Monday, September 11, 2017 10:13 AM

«
...
43
44
45
46
47
...
»

Содержание FX 2018





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для FX 2018

Бренд: Cake Страницы: 13

Бренд: Ohlins Страницы: 4

Бренд: R&G Страницы: 4

Бренд: hepco & becker Страницы: 5

Бренд: Victory Motorcycles Страницы: 332

Бренд: National Cycle Страницы: 5

SPORTCITY CUBE 125

Бренд: APRILIA Страницы: 157

Бренд: R&G Страницы: 9

Бренд: Suzuki Страницы: 526

Бренд: R&G Страницы: 8

Бренд: Honda Страницы: 127

Бренд: SCHUBERTH Страницы: 43

Бренд: Malaguti Страницы: 42

Бренд: Malaguti Страницы: 80

Бренд: Panther Страницы: 47

Бренд: RIEJU Страницы: 79

Бренд: RIEJU Страницы: 116

Бренд: Benelli Страницы: 314

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды