background image

Power Pack

5.8

Power Pack

Power Pack

CAUTION:

 You must leave your motorcycle connected to 

the charger if you expect it to be in storage or unused for 
over 90 days.

The power pack must be charged within 24 hours if fully 
discharged, and charged within 90 days if stored fully 
charged.

Please leave your Zero Motorcycle plugged in whenever 
possible.

1. The power pack is a lithium ion power system. While it 

does require charging, it does not require maintenance.

2. The power pack should be kept away from excessive 

heat. The lithium ion cells should not get above 160°F 
(71°C). Do not store in a hot trailer or leave the power 
pack in direct sunlight.

3. Only an authorized service agent is qualified to have 

access to and troubleshoot the power pack.

4. Dispose of the power pack according to your state and 

local laws. It is encouraged that the power pack be 
recycled rather than disposed of in landfills.

Please contact Zero at [email protected] 
or locate a recycling center in your area.

Zero Owner's Manual (FX).book  Page 8  Thursday, April 5, 2018  1:40 PM

Содержание FX 2015









































































































































Отзывы: