Zero DS 2013 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 124

Zero DS 2013 Скачать руководство пользователя страница 95

Troubleshooting

6.1

Troubleshooting

Troubleshooting

Electric Motorcycle Precautions

Your Zero motorcycle has high voltage components. The high
voltage used by these components is dangerous and can
cause personal injury, severe burns, electric shock and even
fatal injury unless appropriate precautions are taken.

Always observe and obey the instructions on labels attached to
components on the vehicle - they are there for your safety.

Do not touch, attempt to remove or replace any high voltage
parts, wiring (identified by the orange outer sleeving) or
connectors. If the motorcycle is involved in an accident do not
touch any high voltage wiring connectors or the components
connected to the wiring. If a motorcycle fire occurs, extinguish it
with a Class D power-type fire extinguisher.

CAUTION!

Your motorcycle uses high voltage. System

components can be hot to touch during and after starting and
when the motorcycle is shut off. Be careful of both the high
voltage and the high temperature. Obey all labels that are
attached to the motorcycle.

CAUTION!

The motorcycles high voltage system has no user

serviceable parts. Disassembling, removing or replacing high
voltage components, cables or connectors can cause severe
burns or electric shock that may result in serious injury or
death. High voltage cables are colored orange for easy
identification (see First Responder Information illustration at the
back of this manual).

Troubleshooting Your Motorcycle

All of the motorcycles are carefully inspected before they
are delivered. Even after the motorcycles are inspected,
some technical issues can occur. The following information
offers a guide to help you to identify an issue, and if
possible, repair it yourself. If you are unable to solve an
issue with your Zero S/DS electric motorcycle, take it to an
authorized dealer at your convenience. If there is no dealer
in your area call Zero Motorcycles Customer Service.

Zero Owner's Manual (S and DS).book Page 1 Friday, April 26, 2013 4:55 PM

«
...
93
94
95
96
97
...
»

Содержание DS 2013





























































































































Отзывы:

Нет отзывов