Zennio Roll-ZAS страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 53

background image

Roll-ZAS

http://www.zennio.com

Technical Support:

http://zennioenglish.zendesk.com

38

Sending of "0" Delay

: specifies the time, in seconds, after which the value

"0" will be sent, once the corresponding edge has been received.

Sending of "1" Delay

: specifies the time, in seconds, after which the value

"1" will be sent, once the corresponding edge has been received.

Periodical Sending of "0"

:

defines the period, in seconds, for a cyclical

sending of the value "0" after the detection of the corresponding edge. Setting
this to 0 disables the periodical sending.

Periodical Sending of "1"

:

defines the period, in seconds, for a cyclical

sending of the value "1" after the detection of the corresponding edge. Setting
this to 0 disables the periodical sending.

Lock

:

if "Yes" is chosen, a new 1-bit communication object, "[Ix] Lock", will

become visible, making it possible to lock and unlock the corresponding input
(with one "1" or one "0", respectively). During the time the input is locked, any
edges detected in the signal will be ignored.

Sending of Status on Bus Voltage Recovery

: this option allows forcing an

automatic sending to the KNX bus of the state of the input line after a voltage
recovery, with a certain delay (value between 0 and 255, in seconds).

3.4.2

TEMPERATURE PROBE

Configuring an input as a temperature probe brings the following options.

Figure 22

. Input: Temperature Probe

Temperature Sensor Calibration

: setting a certain calibration (in tenths of a

degree) permits correcting the value received from the external temperature
sensor in case it is found to be altered for any reason and therefore different
to other available references, making it possible to synchronise both
references.

«
...
36
37
38
39
40
...
»

Содержание Roll-ZAS






















































Отзывы:

Нет отзывов

Похожие инструкции для Roll-ZAS

C-NaviGator III

Бренд: C-Nav Страницы: 20

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: R82 Страницы: 89

Бренд: Centurion Страницы: 16

Бренд: baby joy Страницы: 11

Бренд: Argo-Hytos Страницы: 38

Бренд: Anest Iwata Страницы: 8

Бренд: Sensitron Страницы: 32

Бренд: ARI-Armaturen Страницы: 17

Бренд: Combi Страницы: 20

Бренд: Hasco Страницы: 78

Бренд: HIKVISION Страницы: 5

Бренд: Nexen Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды