Zenitel VINGTOR STENTOFON EA1400 Скачать руководство пользователя страница 4

Страница: 4 / 17

EA1400/1600 Installation & User Manual

A100K11939

Connectors and Controls

Figure 1: Amplifier Front Panel

Figure 2: Amplifier Rear Panel

2.1. Cabinet

The amplifier is prepared for mounting in a standard 19” rack and will occupy 2HU in height. The amplifier

can also be free-standing on a level, open surface. The amplifier has a built-in cooling fan but the front and

back must be kept free of objects in order to secure sufficient air flow.

2.2. Power

The amplifier is powered by 100-240 VAC 50/60 Hz mains. There is a mains circuit breaker on the cabinet

rear side, and a mains fuse on the Main Board inside the cabinet. The fuse value is 8A. The amplifier must

be grounded with the main cable, or with a 2.5 mm

wire between the amplifier’s ground terminal and a

proven good PE grounding point.

Содержание VINGTOR STENTOFON EA1400


















Результаты поиска

Содержание VINGTOR STENTOFON EA1400

Отзывы:

Похожие инструкции для VINGTOR STENTOFON EA1400

Бренды по названию

Популярные бренды

Zenitel VINGTOR STENTOFON EA1400, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VINGTOR STENTOFON EA1400

Отзывы:

Похожие инструкции для VINGTOR STENTOFON EA1400

Бренды по названию

Популярные бренды