Zenitel VINGTOR STENTOFON EA1400 Скачать руководство пользователя страница 3

Страница: 3 / 17

A100K11939

EA1400/EA1600 Installation & User Manual

Introduction

1.1. Document Scope

This document is intended to provide relevant information on the amplifier features, typical configuration,

basic installation and wiring of the EA1400 and EA1600 amplifier. See product datasheet for technical

details.

1.2. Product Information

Item No.

Item Name

Description

1023121400

EA1400

Exigo Amplifier 1 x 400W

1023131600

EA1600

Exigo Amplifier 1 x 600W

1.3. Publication Log

Revision Date

Author

Status/Comments

1.0

6.3.2020

LK/HKL

Published

1.1

24.8.2020

LK/HKL

Revised Rear Panel, Settings Switch,

Optional Connections

1.4. Rules & Regulations

The EA1400 & EA1600 amplifier and its components have been tested according to the following

regulation:



EN 60945: Fourth edition, 2002

"Maritime navigation and radio communication equipment and systems - General requirements - Methods

of testing and required test results".

Содержание VINGTOR STENTOFON EA1400


















Результаты поиска

Содержание VINGTOR STENTOFON EA1400

Отзывы:

Похожие инструкции для VINGTOR STENTOFON EA1400

Бренды по названию

Популярные бренды

Zenitel VINGTOR STENTOFON EA1400, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VINGTOR STENTOFON EA1400

Отзывы:

Похожие инструкции для VINGTOR STENTOFON EA1400

Бренды по названию

Популярные бренды