Zenitel VINGTOR STENTOFON EA1400 Скачать руководство пользователя страница 15

Страница: 15 / 17

A100K11939

EA1400/EA1600 Installation & User Manual

Service

5.1. Service Information

All service on this unit should be performed by qualified service technicians only.



Contact your local Vingtor-Stentofon dealer or representative for service.

WARNING!
Always disconnect the mains power cable before opening the cabinet to avoid electrical shock

hazard and possible damage to the equipment.

5.2. Fuse Replacement

Mains Voltage Protection

There is one replaceable fuse:



on the Main Board near the mains inlet inside the cabinet

A blown fuse normally indicates a malfunction of the amplifier or a short term overload.

Always replace with fuses of same type (Littelfuse 0215008.TXP or Schurter 34.3126) and value

(8AT). On recurring fuse blows, contact qualified service personnel.

Содержание VINGTOR STENTOFON EA1400


















Результаты поиска

Содержание VINGTOR STENTOFON EA1400

Отзывы:

Похожие инструкции для VINGTOR STENTOFON EA1400

Бренды по названию

Популярные бренды

Zenitel VINGTOR STENTOFON EA1400, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VINGTOR STENTOFON EA1400

Отзывы:

Похожие инструкции для VINGTOR STENTOFON EA1400

Бренды по названию

Популярные бренды