KEY FEATURES
• Compact, high-resolution plug & play reversing camera for replacement of
the original 3
rd
OE brake light assembly, for commercial vehicles, vans
and minibuses based on the 7
th
generation FORD Transit incl. motorhomes
and camper vans from 2019 Facelift and up
• Rugged injection molded red plastic main body with stainless steel clip-on
mounting clamps
• ECE 148R certifi ed brake light assembly (retaining the road homologation
approval)
• Cam sensor with 140° diagonal viewing angle for a wide surveillance area
behind the vehicle
• Manually adjustable vertical image section of the camera sensor with +20° to
-20° range to hit individually preferred fi eld of view
• IR-LED lighting with 6 LEDs and dynamic brightness control via LDR element
• Integrated microphone for monitoring of environmental sounds via control
unit
• Separable 3-piece system cable of 10 m length with nut secured 4-pin
connectors
ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙ Switzerland,
EU Legal Representative:
ACR S & V GmbH ∙ Industriestr. 35 ∙ D-79787 Lauchringen ∙ Germany www.zenec.com
R
ev.
E
TECHNICAL SPECIFICATIONS
Image device Cam:
SHARP RJ2331 CCD sensor
(with AA9050)
Image sensor type:
1/3“ / 8.5 mm CMOS sensor
TV system:
NTSC / 30 fps
View angle:
140° diagonal
Native sensor pixel matrix:
976 (H) x 494 (V)
Image relevant resolution:
700 TV lines
Lens focal length:
2.6 mm
Frame rate:
30 fi elds/sec., interlaced
Signal to noise ratio:
> 48 dB
Dynamic contrast:
> 60 dB
Light sensitivity:
30 Lux with IR-LED ON
Video output:
1.0 ±0.2 Vp-p, 75 Ω, CVBS
White balance:
Auto
Backlight compensation:
Auto
Gamma correction:
0.45
Gain control:
Auto
Sync system:
Auto
Power supply:
12 DCV
Current consumption (@12 V DC): 80 mA ±10 mA
IP protection rating:
IP68
Operating temperature:
-20° C ~ +70° C
CAUTION:
■
The camera is water- and dustproof and has been licensed according to the international standard IP68. However, vehicle cleaning using high pressure
water and steam jet devices may still lead to damage of IP68 rated camera models by water intrusion. Keep a distance of at least one meter between the
water nozzle and the camera housing.
Model
Type
Model Year
FORD Transit, all versions*
7
th
Generation, 2019 Facelift
as of 2019
*Commercial vehicles, vans, minibuses and other versions based on 7th Gen vehicle hull
structure such as motorhomes with swing out rear doors and 3rd brake light at rear top section.
Only for direct mounting, not compatible with vehicles which are equipped with optional brake
light plastic housing.
*FORD Transit Custom vehicles cannot be extended directly with the ZE-RCE3804 without
modifi cation, as the power supply plug is too long and protrudes on the inside.
ZE-RCE3804
ZE-RCE3804
MOUNTING INSTRUCTIONS
REAR VIEW CAMERA FOR FORD TRANSIT
10.0 m
Red: CAMERA PWR (+12V)
Black: GND
0.17 m
0.15 m
Yellow RCA:
Camera (CVBS) video signal
White RCA:
Microphone audio signal
0.7 m
Bright reflecting Silver (chrome)
Illuminated
Infrared
Pantone Warm Red CV
Camera
Radio
+12V
GND
VIDEO
AUDIO
(female)
(male)
1
2
4
3
VIDEO
AUDIO
+12V
GND
4
3
1
2
Pin assignment for M12 4pin connector
Input socket for brake light power
supply connector of vehicle
INSTALLATION
:
The original brake light insert is unclipped via the service
opening in the rear ceiling area of the Transit. The clips can be
released with light pressure from below (3 mm screwdriver).
Now unplug the power supply plug on the original brake light
insert.
Lay the 10 m extension cable from the dashboard to the cam-
era's mounting hole. Connect the A/V RCA plugs to the rear
camera A/V inputs of your control unit as shown in the cable
diagram above. Now connect the red/black power supply ca-
bles to the camera power supply cables of your control unit.
1.
Clean the surface of the recessed inside edge of the
mounting hole with a degreasing detergent. This is necessary
to ensure proper adhesion of the seal.
2.
Stick the "Memory Foam" sealing tape into the recess at
the installation opening, whereby the sealing tape should lie
exactly against the inner edge. If the ambient temperature is
below 20° C, heat the sealing tape with a hot air blower to
facilitate the installation of the camera.
3.
Connect the camera main cable and the power supply ca-
ble to the ZE-RCE3804*
1
. Insert the camera into the installa-
tion opening in an angled position, as shown in Figure 3, so
that the upper clamps are already in the fi nal position. Press
the lower part of the camera fi rmly and push the camera up-
wards with a strong jerk. The brackets will audibly click into
place.
*
1
FORD Transit Custom vehicles cannot be extended directly
with the ZE-RCE3804 without modifi cation, as the power
supply plug is too long and protrudes inside.
1
2
3
UK Authorised Representative
(for authorities only)
ProductIP (UK) Ltd.
8, Northumberland Av.
London WC2N 5BY
UK Declaration of Conformity
Hereby, ACR Brändli + Vögeli AG declares that ZENEC
ZE-RCE3804 is UKCA compliant – the UK Declaration
of Conformity can be accessed via the following Internet
address:
http://www.zenec.com
(see link „Product
Conformity Documents“ in the footer area of the page).
