Zelmer 43Z011, Руководство пользователя, Страница: 95 / 98

97
GW43-008_v02
QUESTIONS AND ANSWERS CONCERNING THE APPLIANCE
Problem Cause Solution
Smoke comes out of the baking
compartment or the vents.
The ingredients stuck to the
baking compartment or to the
outside of the baking tin.
Unplug the appliance and clean the outside of the baking tin or the
baking compartment.
The bread goes down in the
middle and is moist on the
bottom.
The bread was left for too long
in the baking tin after baking and
warming.
Take the bread out off the baking tin before the end of the warming
function.
It is difficult to take the bread out
of the baking tin.
The bottom of the total is stuck to
the kneading peg.
Clean the kneading peg and shaft before the next time you bake bread.
If necessary, fill the container with warm water and leave for 30 minutes.
This way the kneading pegs can be easily removed and cleaned.
The ingredients are not mixed or
the bread is not baked properly.
Incorrect program setting. Check the selected menu and other settings.
The START/STOP button was
pressed while the machine was
working.
Do not use the ingredients and start the whole process again.
The lid opened several times
while the machine was working.
The lid can only be opened if the time left on the display is more than
1:30.
Make sure the lid was closed properly.
Long blackout while the machine
was working.
Do not use the ingredients and start the whole process again.
The rotation of the kneading
pegs is blocked.
Check if the kneading pegs are not blocked by for example grains, etc.
Pull out the baking tin and check if the drivers turn. If this is not the
case, return the appliance to a service point.
The appliance does not start.
The audible signal goes off. The
display shows the symbol H:HH.
The appliance is still hot after the
previous baking process.
Press and hold the START/STOP button until the normal program code
appears on the display. Unplug the appliance. Take out the baking
tin and leave to cool at room temperature. Plug in and restart the
appliance.
The appliance does not start.
The audible signal goes off. The
display shows the symbol “LLL”.
Program or electronic error.
Start the test run. Press and hold the menu button, unplug the appliance
and then plug it in again. Release the button. The appliance will perform
a test run. Unplug the appliance again. The normal program code “1P”
should appear on the display. If this is not the case, return the appliance
to a service point.
The display shows the symbol
“EEE”.
Program or electronic error. Please proceed according to the description above.
The display shows the symbol
“000” after restarting the
appliance.
The appliance was switched off
by pulling out the plug during
the warming phase. The basic
program “P1” was not set.
Always use the START/STOP button to stop the appliance. To restart
the appliance: Press and hold the START/STOP button for 10 seconds
until the symbol “P” together with the program number appears on the
display.
Never immerse the appliance into water or fill the baking
compartment with water!
For easy cleaning the lid can be removed by positioning
●
it vertically and pulling it out.
Wipe the outside of the baking tin with a damp cloth. The
●
inside of the tin can be washed with dishwashing liquid.
Do not immerse the tin into water.
Clean the kneading pegs and the drive shaft immediately
●
after use. If the kneading pegs remain in the tin, it will
be difficult to remove them afterwards. In such a case fill
the container with warm water and leave for 30 minutes.
Next remove the kneading pegs.
The baking tin has a non-stick coating. Do not use
●
metal objects that could scratch the coating. The color
of the coating will change during the course of use. This
is a normal situation. This change does not affect the
effectiveness of the coating in any way.
Make sure the appliance has completely cooled down
●
and is dry before storing. Store the appliance with the
lid closed.