Zeiss VISUREF 150 Скачать руководство пользователя страница 113

Страница: 113 / 134

Maintenance and care

000000-2227-967-GA-GB-281021

107

Maintenance

Replacing the printer paper roll

If a red line appears on the paper, or if ‘NO PAPER’ message is displayed on

the screen bottom, the printer paper unit must be refilled.

Printer paper insertion slit

Fig. 66

Inserting printer paper

•

Turn the joystick clockwise to lift up the upper part of the body case.

•

Open the printer cover.

•

Install the paper roll so that the printable side of the paper (smoother

and shinier than the other side) faces upwards when fed through to the

printer assembly.

•

Feed the printer paper from below into the slit of the black printer unit,

then push it up gently. If it is correctly positioned, the printer will

automatically pull the paper upward for printing.

•

Insert the end of the paper (emerging from the printer) into the slit in the

printer cover, then close the cover.

•

Carefully pull out the end of the paper if necessary.

Содержание VISUREF 150







































































































































Результаты поиска

Содержание VISUREF 150

Отзывы:

Похожие инструкции для VISUREF 150

Бренды по названию

Популярные бренды

Zeiss VISUREF 150, Руководство пользователя

Результаты поиска

Содержание VISUREF 150

Отзывы:

Похожие инструкции для VISUREF 150

Бренды по названию

Популярные бренды