Zeiss EVO Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 180

Zeiss EVO Скачать руководство пользователя страница 18

2 Safety | 2.5 Safety Devices and Interlocks

ZEISS

Position and Figure of the Safety La-
bel

Description

16

At the CEE connector

Risk of electrical shock

Residual voltage at the mains plug after unplug-
ging.

Wait at least 5 s after unplugging the mains plug
before touching the pins of the mains plug.

Position and Figure of the Type Plate

Description

13

At the rear of the microscope

Carl Zeiss Microscopy GmbH

73447 Oberkochen, Germany

Serial number

50 - 60 Hz

max. 16 A

EVO15

354900-9041-000

1/N/PE

Made in UK/GB

230 VAC

Manufactured in year 2017

The

Type plate

contains a unique serial number,

the EVO model designation with the according
part number, the manufacturing year, and the
mains voltage for which the EVO is configured,
either 230 VAC or 120 VAC.

Order no. 354900-9040-000 (EVO10)

Order no. 354900-9041-000 (EVO15)

Order no. 354900-9042-000 (EVO25)

2.5 Safety Devices and Interlocks

In order to prevent injuries and/or property damage, the Microscope System is equipped with sev-
eral safety devices and interlocks. In case of defect or damage, the affected parts and the Micro-
scope System must be taken out of operation immediately and must be secured against uninten-
tional use.

To verifying the safety of the Microscope System, please contact your ZEISS service representative.
Please keep the service logs and logbooks.

2.5.1 Protective Cover Panels

Due to hazardous voltages and X-rays inside the microscope, the microscope is equipped with
protective cover panels.

18

Instruction Manual ZEISS EVO | en-US | Rev. 10 | 354706-0780-006

«
...
16
17
18
19
20
...
»

Содержание EVO





















































































































































































Отзывы:

Нет отзывов