zeeltronic PDCI-44V Скачать руководство пользователя страница 1

 

 

- 1 -

 

www.zeeltronic.com 
[email protected] 
 
updated 04.04.2011 
program version: 20.310311 
 

USER MANUAL  

PDCI-44V PROGRAMMABLE CDI IGNITION AND PV CONTROLLER 

 
 
Limit values: 
- minimum revs 

200 RPM 

- maximum revs 

20000 RPM 

- minimum supply voltage 

7 Volts 

- maximum supply voltage 

18 Volts 

- normal operating voltage 

12 ÷ 14,5 Volts 

- stand-by current draw  

                    < 0.09 Amp 

- current draw at 1300 RPM 

< 0.5 Amp 

- current draw at 12000 RPM 

~ 3 Amp  

- maximum continuous current for shift light and power jet output 

1 Amp  

- peak current for shift light and power jet output  

5 Amp 

- constant spark energy from idle to 14000 RPM 

>35mJ 

 
Circuit is protected against reverse supply voltage (wrong connection). 
 
Features: 
- fast power-up 
- full power starting spark energy already at 7Volts power supply 
- two isolated input (pickup) 
- four independent ignition coil outputs 
- individual advance/retard of each ignition coil output 
- store and load function for two ignition maps 
- external switch for changing ignition map while riding 
- TPS input (Throttle Position Sensor) 
- shift light output 
- 2 power jet outputs 
- duty cycle solenoid output (for regulating A/F ratio on some carburettors) 
- quick shift (shift kill) 
- soft rev limit (three stage rev limit) 
- reduced spark at high revs with closed throttle (TCT mode) 
- tachometer output 
- easy and fast programming on the field, via hand held programmer 
- programming while machine running - you can immediately see effects 
- each curve can be set in 4 to 12 curve points 
- 3D interpolated ignition map, if TPS selected 
- signal delay compensation 
- instant monitoring of rev's and angle, via LCD(hand held programmer) 

Содержание PDCI-44V















Отзывы: