background image

Seite 10/69

Seite 10/41

FDM-T-Sports

2.2.3. Safety instructions for the treadmill

 The treadmill belonging to the FDM-T measuring system is a very powerful device. 

For safe operation of the FDM-T system it is mandatory to adhere exactly to the 
safety regulations described in the following.

 The measuring procedure on the treadmill must never be commenced without a thorough 

instruction of the patient by trained personnel. No measurements may be taken without a supervisor.

 Do not place the treadmill on an unstable ground.

 Do not set up the system near a source of heating or in direct sunlight in front of a window as 

a strong rise in temperature can lead to inaccurate measuring results.

 Directly behind the treadmill it is mandatory for a safety zone of 2 m in length and 1 m in width

to be kept free, and ought to be padded (with a soft mat). No items may be left in this zone during 
operation (such as video camera, lighting equipment etc.).

 Dangerous drawing-in gaps are located at the rear end of the running belt and along its sides and

(if existing) on the elevating mechanism. Do not wear any loose clothing that could get caught up 
in the rollers. Make sure that if a person trips over, their long hair, loose clothing, jewellery, etc.,
do not encounter the rear part of the treadmill belt (e.g., wear a hair net). Due to danger of 
stumbling, do not place any clothing or jewellery on or within close proximity of the treadmill.

 Never use the treadmill without the safety clip being fastened to your clothing and always be sure 

that the folding mechanism (if existing) is properly locked during operation. (Please also be sure to 
read the safety instructions in the user manual supplied by the treadmill manufacturer.)

 During operation, the emergency STOP facilities must always be within easy reach for the user and

the operating personnel.

 The patient should walk slowly to begin with. Then gradually speed can be increased after a few 

minutes, depending on the patient’s physical condition. Improper or excessive strain through tests 
resp. measurements can have harmful effects on health.

 Never jump onto the running belt and never jump off it whilst it is running. Never stop walking 

while the treadmill is running, never turn round or step sideward or backwards. Should movement 
patterns of this kind be necessary for your measurements, please make sure to use a type of tread-
mill with a safety arch, protection against falling and a “fall stop” chest belt.

 Pull out the power plug before transporting the treadmill.

Содержание FDM-T-Sports










































Отзывы: