ZCS AZZURRO 1PH HYD3000-ZP1 Скачать руководство пользователя

Страница: 127 / 195

User’s Manual 1PH HYD3000-HYD6000-ZP1

Rev. 1.0 01/09/2023

Identification: MD-AL-GI-00

Rev. 1.1 of 27/01/2023 - Application: GID

126/193

11.

Technical specifications

TECHNICAL DATA

1PH HYD 3000

ZP1

1PH HYD 3600

ZP1

1PH HYD 4000

ZP1

1PH HYD 4600

ZP1

1PH HYD 5000

ZP1

1PH HYD 6000

ZP1

DC photovoltaic input

Typical DC power *

4500W

5400W

6000W

6900W

7500W

9000W

Independent MPPTs/Strings each MPPT

2/1

Maximum DC voltage

550V

Start-up voltage

100V

Nominal DC voltage

360V

MPPT range in DC

85V-520V

Maximum DC input current each MPPT

16A/16A

Maximum absolute DC input current each MPPT

22.5A/22.5A

Battery input data

Type of batteries

HV ZBT 5K + BDU Unit

Nominal voltage

400V

Voltage range

300V-435V

Maximum charge/discharge power

3000W

3680W

4000W

4600W

5000W

6000W

Allowed temperature range**

-10°C/+50°C

Maximum charge current

20A (setabke)

Maximum discharge current

20A (setable)

Charge curve

Managed by integrated BMS

Depth of Discharge (DoD)

0%-90% (setable)

AC output

Nominal AC Power

3000W

3680W

4000W

4600W

5000W

6000W

Maximum AC Power

3300VA

3680VA

4400VA

4600VA

5500VA

6600VA

Maximum AC current each phase

13A

16A

17.4A

20A

21.7 A

26A

Type of connection/Nominal AC grid voltage

Single phase L/N/PE 220,230,240V

AC voltage range

180V-276V

(according to local standards)

Nominal AC frequency

50Hz/60Hz

AC frequency reange

44Hz-55Hz / 54Hz-66Hz

(according to local standards)

Total Harmonic Distortion (THD)

< 3%

Power Factor

1 default (/- 0.8)

Active power grid injection

Setable by display

EPS (Emergency Power Supply) output

Maximum Power in EPS***

3000VA (4500VA

for 10s)

3680VA (5520VA

for 10s)

4000VA (6000VA

for 10s)

4600VA (6900VA

for 10s)

5000VA (7500VA

for 10s)

6000VA (9000VA

for 10s)

Voltage and frequency in EPS

Single phase 230V 50Hz/60Hz

Maximum current in EPS

13A

16A

17.4A

20A

21.7 A

26A

Total Harmonic Distortion (THD)

< 3%

Switch time

< 10ms

Efficiency

Maximum Efficiency

97.7%

97.8%

Euro efficiency

97.0%

97.1%

Efficiency MPPT

>99.9%

Standby consumption

< 10W

Protections

Internal interface protection

Yes

Safety protections

Anti islanding, RCMU, Ground Fault Monitoring

DC reverse polarity protection

Yes

DC switch

Integrated

Overheating protection

Yes

Overvoltage catergory/Protection class

Overvoltage Category III (AC) / II (DC) / Protective class I

Integrated dischargers

AC/DC MOV: Type 3 standard

Battery Soft start

Yes

Standard

EMC

EN 61000-3-2/3/11/12, EN 61000-6-2/3

Safety standards

IEC 62116, IEC 61727, IEC 61683, IEC 60068-1/2/14/30, IEC 62109-1/2

Grid standards

Grid standards and certificates available on www.zcsazzurro.com

Communication

Communication Interfaces

Wi-Fi/4G/Ethernet (optional), RS485 (

proprietary protocol

), USB

Additional connection

AC Current sensor connection input or dedicated meter

Environmental data

Temperature working range

-10°C...+50°C (power derating over 45

℃

)

Topology

Trasformerless

Environmental protection degree

IP65

Humidity range

5%.....95% no condensing

Maximum operative altitude

4000m

Acustic noise

< 35dB @ 1mt

Weight

22.5Kg

Cooling system

Natural cooled

Dimensions (H*W*L)

410mm*708mm*170mm

Display

LED display and APP

Warranty

10 years

Содержание AZZURRO 1PH HYD3000-ZP1




































































































































































































Результаты поиска

Содержание AZZURRO 1PH HYD3000-ZP1

Отзывы:

Похожие инструкции для AZZURRO 1PH HYD3000-ZP1

Бренды по названию

Популярные бренды

ZCS AZZURRO 1PH HYD3000-ZP1, Руководство пользователя

Результаты поиска

Содержание AZZURRO 1PH HYD3000-ZP1

Отзывы:

Похожие инструкции для AZZURRO 1PH HYD3000-ZP1

Бренды по названию

Популярные бренды