ZCS 1100TL-G3 Скачать руководство пользователя страница 24

Страница: 24 / 69

1.1K~3.3KTL-G3

User manual

- 19 -

Electrical Connections

Outlines of this chapter

This topic describes the 1.1K~3.3KTL-G3 inverter electrical connections.

Read this part carefully before connecting cables.

NOTE:

Before performing electrical connections, ensure that the DC switch is OFF.

Since the stored electrical charge remains in a capacitor after the DC switch is turned OFF.

So it

’

s necessary to wait for at least 5 minutes for the capacitor to be electrically discharged.

Installation and maintenance of inverter, must be operated by

professional electrical engineer.

Attention

PV modules generate electric energy when exposed to sunlight and

can create an electrical shock hazard. Therefore, before connecting DC
input power cable, cover PV modules using opaque clot

Danger

For 1.1K~2.2KTL-G3,open-circuit voltage(Voc) of module arrays

connected in series must be

≤

500V;For 2.2K~3.3KTL-G3, it must be

≤

550V.

The power of PV grid-tied system which contain by several the

1.1K~3.3KTL-G3 inverters must be < 3.68kw in Germany.

Note

The connected PV modules must have an IEC 61730 Class A ratin

IscPV(absolute maximum)

15A

Maximum output over current

protection

1100TL-G3

5.3A

1600TL-G3

7.7A

2200TL-G3

10.6A

2700TL-G3

13A

3000TL-G3

14.5A

3300TL-G3

16A

The decisive voltage class(DVC)

NOTE:

The DVC is the voltage of a circuit which occurs continuously between any two

live part in the worst-case rated operating condition when used as intended.

Содержание 1100TL-G3






































































Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды

ZCS 1100TL-G3, Руководство пользователя

Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды