Zanussi ZEL 296, Инструкция пользователя

Страница: 7 / 20

7
TOO WARM
CCOO2
ZANUSSI
Cool Check Guide
The guide consists of a temperature sensitive strip
sealed in a shelf trim.
When the fridge is operating at the safe temperature
to store food the guide will appear black. If the
temperature rises above this level the guide will
show the words TOO WARM.
Positioning of the Cool Check
The shelf with the cool check temperature guide
must be placed in the fridge according to the
instructions located on the fridge wall and always
ensure the guide is at the front.
If the Cool Check shows TOO WARM
In certain conditions the temperature guide may
show TOO WARM if:
• The fridge is switched off
• The door has been recently opened
• A quantity of warmer food has been introduced to
the fridge
• The fridge temperature is above the
recommended maximum for the safe storage of
food.
The cool check will change to show “TOO WARM“
very quickly after the door has been opened. It will
however take a number of hours to return to black,
indicating that the temperature is correct.
The appliance should be left overnight and the cool
check examined in the morning. If the cool check
shows TOO WARM, turn the thermostat to a colder
setting leave overnight and examine again the
following morning.
Hints and Tips
• The guide is only suitable for use in the model
supplied.
• The guide will not operate in a freezer
compartment.
• When cleaning the shelf take care not to immerse
in water, and wipe away any spills.
14
INSTALLATION
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located at the left on the inside of the
appliance.
The following table shows which ambient
temperature is correct for each climate classification:
SN +10°C to + 32°C
N +16°C to + 32°C
ST +18°C to + 38°C
T +18°C to + 43°C
It should be located in a dry atmosphere, out of
direct sunlight and away from extreme temperature
e.g. not next to a boiler or radiator, or in a very cold
room e.g. an outhouse, where the temperatures may
fall below 10°C (50°F). If these temperatures are
exceeded i.e. colder or warmer, then the appliance
may not operate correctly.
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
must also be at least 100 mm (4”) distance between
the top of the cabinet and any overhanging kitchen
furniture (A). Ideally, the appliance should not be
positioned beneath overhanging furniture (B).
There should also be a gap of 25 mm either side of
the appliance. Do not obstruct the space
underneath. The back of the cabinet may be placed
close to the wall but must not touch it. DO NOT
install in places with restricted ventilation.
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers.
D200
D594
100 mm
10 mm
10 mm
A
B
NP007
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Rear spacers
In the bag with the documentation, there are two
spacers which must be fitted as shown in the figure.
Slacken the screws and insert the spacer under the
screw head, then re-tighten the screws.
Important
It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
on “Door reversal”.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.