Z3 Technology Z3-MVE-02 Скачать руководство пользователя страница 7

Страница: 7 / 36

DOC-USR-0038-05

_______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

3.0

FEATURES

The Z3-MVE-02 is a high definition, low-cost, network-enabled media encoder with the following features:



HD resolutions up to 1920x1080 including 1080i, 1080p30 and 720p



Supported video includes H.264 and MPEG-2



Standard Definition encoding for ISDB-T, DVB-H, and other standards



Low latency encode mode



Video Inputs: Composite, Component, HD-SDI, DVI, HDMI (Optional ASI Input)



Input video resizer supports many standard resolutions



Video Output Interfaces: Ethernet and ASI



Outputs RTP, RTMP, or MPEG-2 Transport Stream



Supports fractional resolutions and frame rates



Video Frame Rate: 50Hz or 60Hz



SD Card interface for local storage and firmware updates



USB interface for mass storage devices or other peripherals



Web-based configuration software for user-friendly configuration and control



RS232 serial port for technical configuration and control



Operating: 0 to 45 degrees C at 20-80% relative humidity (non-condensing)



Storage: -40 to 70 degrees C at 20-80% relative humidity (non-condensing)



Measurements: 203mm x 114mm x 41mm



Weight: 682g

Содержание Z3-MVE-02





































Результаты поиска

Содержание Z3-MVE-02

Отзывы:

Похожие инструкции для Z3-MVE-02

Бренды по названию

Популярные бренды

Z3 Technology Z3-MVE-02, Инструкция пользователя

Результаты поиска

Содержание Z3-MVE-02

Отзывы:

Похожие инструкции для Z3-MVE-02

Бренды по названию

Популярные бренды