Z3 Technology Z3-MVE-02 Скачать руководство пользователя страница 33

Страница: 33 / 36

DOC-USR-0038-05

_______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

8.2 Decoder Options

Parameter

Options (default in bold)

Notes

Input Interface

Ethernet

DVB-ASI

Where to get the input stream to decode.

Input Format

RTP

RTSP
MPEG-2 TS
MPEG-2 TS over RTP

The format of the incoming stream.  These
mirror the options on the encode side.  There
is also an RTSP option.  RTSP is used with
sources such as VLC and the TI IP Network
Camera.

RTP/TS IP: Port

x.y.z.w:pppp (

225.1.2.3:8888

) The IP address and port being streamed to.

Video Codec

H.264

The video format being used in the incoming
stream. Only H.264 is supported in this
release.

Audio Codec

AAC

MPEG
PCM
None

The audio codec being used in the incoming
stream. MPEG decodes MP1L2 and MP3.
Available options depend on what was
licensed.

MVE Flag

Yes

Set this flag if the streaming source is another
Z3-MVE-02, or an encoder from Z3’s DM368
family of products.

Output Interface

SDI

Only SDI output is supported

Video Frame Rate

50Hz

60Hz

Use to select between NTSC and PAL
monitors, for example.

Local IP Address

192.168.X.XX (

192.168.0.65

)

Sets the IP address of the Z3-MVE-02.
Disregarded if “Use DHCP” is checked.

Local Netmask

255.255.X.X (

255.255.0.0

)

Sets the Netmask of the Z3-MVE-02.
Disregarded if “Use DHCP” is checked.

Default Gateway

192.168.X.XX (

192.168.0.1

)

Can generally leave as “192.168.0.1” --
disregarded if “Use DHCP” is checked.

Stop Decoder [Button] -----

Stop the current decode session.

Use DHCP [Checkbox]

On /

Off

On -> Use DHCP to get IP address at boot-up
(see “Using DHCP”).

Start Decoder
[Button]

-----

Start a decode session.

Status

IDLE

, STOPPED, RUNNING

Current status of the decoder.

Load Factory Default
Settings [Button]

-----

Load settings installed at the factory.

Load User Settings

-----

Load user settings previously saved.

Save User Settings

-----

Save current settings for later use.

Содержание Z3-MVE-02





































Результаты поиска

Содержание Z3-MVE-02

Отзывы:

Похожие инструкции для Z3-MVE-02

Бренды по названию

Популярные бренды

Z3 Technology Z3-MVE-02, Инструкция пользователя

Результаты поиска

Содержание Z3-MVE-02

Отзывы:

Похожие инструкции для Z3-MVE-02

Бренды по названию

Популярные бренды