Z3 Technology Z3-DME-02 Скачать руководство пользователя страница 7

Страница: 7 / 44

CONFIDENTIAL

DOC-USR-0054-02

____________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

3.0

FEATURES

The Z3-DME-02 is a high definition, low-cost, network-enabled media encoder with the following features:



HD resolutions up to 1920x1080 including 1080i, 1080p60 and 720p



Standard Definition encoding for ISDB-T, DVB-H, and other standards



Video Inputs: 3G-SDI, Composite



Video Outputs: 3G-SDI, HDMI



On-board video scaler provides full screen with all resolutions



Outputs RTP, RTMP, or MPEG-2 Transport Stream



Supports fractional resolutions and frame rates



2 USB 2.0 Interfaces for local storage



Web-based configuration software for user-friendly configuration and control



RS232 serial port for technical configuration and control



Operating Temp: 0 to 40 degrees C at 20-80% relative humidity (non-condensing)



Storage Temp: -40 to 70 degrees C at 20-80% relative humidity (non-condensing)



Measurements: 233x 129x 35 mm (9.17 x 5.07 x 1.38 in)



Weight: 921 g (2.03 lb)

Содержание Z3-DME-02













































Результаты поиска

Содержание Z3-DME-02

Отзывы:

Похожие инструкции для Z3-DME-02

Бренды по названию

Популярные бренды

Z3 Technology Z3-DME-02, Инструкция пользователя

Результаты поиска

Содержание Z3-DME-02

Отзывы:

Похожие инструкции для Z3-DME-02

Бренды по названию

Популярные бренды