MANUAL • MANUEL •
MANUAL
Z-Wave
®
Certified Wireless Lighting Control
Certifié Z-Wave
®
Commande d’éclairage sans fil
Control inalámbrico para iluminación certificado por Z-Wave
®
ezzwave.com
SPECIFICATIONS
ZW4007
Power: 120-277VAC, 60Hz, single phase
Signal (frequency): 908.4/916MHz
Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave
receiver module
Operating temperature range: -22 to 104° F (-30 to 40° C)
For outdoor use in dry, damp or wet locations
Contact ratings: 120-277VAC, 40A resistive single phase
120-277 VAC, 20A ballast load (inductive) single phase
125VAC, 15A tungsten
250VAC, 5A tungsten
1HP@120VAC,
2HP @ 240VAC
SPÉCIFICATIONS
ZW4007
Tension : Entre 120 et 277VCA, 60Hz, monophasé
Signal (fréquence) : 908.4/916MHz
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus
proche allant jusqu’à 150 pi
Plage de températures de fonctionnement : De -30 à 40° C (de -22 à 104° F).
Pour une utilisation extérieure dans des endroits secs, humides ou mouillés.
Caractéristiques nominales des contacts : Entre 120 et 277VCA, 40A de résistivité,
monophasé
Entre 120 et 277VCA, 20A de charge de délestage (inductif), monophasé
125VCA, 15A tungstène
250 VCA, 5A tungstène
1HP à 120VCA
2HP à 240VCA
ESPECIFICACIONES
ZW4007
Electricidad: 120-277VCA, 60 Hz, monofásica
Señal (frecuencia): 908.4/916MHz
Alcance: Hasta 150 pies en línea recta entre el controlador inalámbrico y el módulo
receptor Z-Wave más cercano.
Rango de temperatura de funcionamiento: -30 a 40° C (-22 a 104° F)
Para uso en exteriores secos, húmedos o mojados
Regímenes nominales de contacto: 120-277VCA, monofásica resistiva 40A
120-277VCA, 20A balasto (inductivo) monofásica
125VCA, 15A tungsteno
250VCA, 5A tungsteno
1HP@ 120VCA
2HP@ 240VCA
• SE RECOMIENDA QUE LA INSTALACIÓN LA
REALICE UN ELECTRICISTA AUTORIZADO.
PRECAUCIÓN
RIESGO DE DESCARGA ELÉCTRICA
• PUEDE QUE SEA NECESARIO DESCONECTAR
MÁS DE UN INTERRUPTOR PARA
DESENERGIZAR EL DISPOSITIVO ANTES
DE REALIZAR EL MANTENIMIENTO.
• ALTA TENSIÓN (ES POSIBLE QUE HAYA MÁS
DE UNA FUENTE DE ENERGÍA), DESCONECTE
TODAS LAS FUENTES DE ENERGÍA ANTES
DE REALIZAR EL MANTENIMIENTO.
• USE SÓLO CONDUCTORES DE COBRE.
• CIERRE LA TAPA DESPUÉS DE USAR.
• APRIETE LAS CONEXIONES A 25LBF-IN.
• USE CABLE DEL CALIBRE CORRECT (8-
14AWG) TENIENDO COMO BASE EL CÓDIGO
DE NORMAS DE ELECTRICIDAD LOCAL DE
UN RÉGIMEN NOMINAL DE AL MENOS 80°
C (CABLE MONOCONDUCTOR DE 8AWG).
• IMPERMEABLE, APROBADO PARA
USO EN EXTERIORES.
• LONGITUD DE CABLE SIN
AISLAMIENTO 1/2PULG.
CONEXIÓN A TIERRA
• EL CÓDIGO ESTADOUNIDENSE DE
NORMAS DE ELECTRICIDAD EXIGE QUE LA
PUESTA A TIERRA SEA CONTINUA, CON
EL CONTACTO ELÉCTRICO ADECUADO EN
TODOS LOS CONDUCTORES DE PUESTA
A TIERRA, LAS CANALETAS METÁLICAS
Y LOS BORNES DE PUESTA A TIERRA.
• RECOMMEND INSTALLATION BY
LICENSED ELECTRICIAN.
CAUTION
RISK OF ELECTRIC SHOCK
• MORE THAN ONE DISCONNECT SWITCH
MAY BE REQUIRED TO DE-ENERGIZE
THE DEVICE BEFORE SERVICING.
• HIGH VOLTAGE (THERE MAY BE MORE THAN
ONE SOURCE OF SUPPLY) DISCONNECT ALL
POWER SOURCES BEFORE SERVICING.
• USE COPPER CONDUCTORS ONLY.
• CLOSE THE COVER AFTER USE.
• TIGHTEN CONNECTIONS TO 25LBF-IN.
• USE CORRECT GAUGE WIRE (8-14AWG)
BASED ON LOCAL ELECTRICAL CODE OF AT
LEAST 80° C RATING (SINGLE CORE IN 8AWG).
• RAINTIGHT, APPROVED FOR OUTDOOR USE.
• WIRE STRIP LENGTH 1/2IN.
GROUNDING
• NATIONAL ELECTRICAL CODE REQUIRES
GROUNDING MUST BE CONTINUOUS AND
IN PROPER ELECTRICAL CONTACT IN ALL
GROUNDING CONDUCTORS, METALLIC
CONDUITS AND GROUNDING TERMINALS.
• INSTALLATION EFFECTUÉE PAR UN
ÉLECTRICIEN QUALIFIÉ RECOMMANDÉE.
ATTENTION
RISQUE DE CHOC ÉLECTRIQUE
• PLUS D’UN SECTIONNEUR PEUT ÊTRE
NÉCESSAIRE POUR METTRE L’APPAREIL
HORS TENSION AVANT UNE RÉPARATION.
• HAUTE TENSION (IL PEUT Y AVOIR PLUS
D’UNE SOURCE D’ALIMENTATION), COUPER
TOUTES LES SOURCES D’ALIMENTATION
AVANT DE PROCÉDER À LA RÉPARATION.
• UTILISER SEULEMENT DES
CONDUCTEURS DE CUIVRE.
• REFERMER LE COUVERCLE
APRÈS L’UTILISATION.
• SERRER LES CONNEXIONS À 25LBF/PO.
• UTILISER UN FIL DU BON CALIBRE (8-14AWG),
D’APRÈS LE CODE DE L’ÉLECTRICITÉ LOCAL,
AYANT UNE TEMPÉRATURE NOMINALE D’AU
MOINS 80° C (FIL UNIPOLAIRE 8 AWG).
• ÉTANCHE À LA PLUIE, APPROUVÉ
POUR USAGE À L’EXTÉRIEUR.
• LONGUEUR DE FIL À DÉNUDER 1/2 PO.
MISE À LA TERRE
• SELON LE CODE NATIONAL DE
L’ÉLECTRICITÉ, LA MISE À LA TERRE DOIT
ÊTRE CONTINUE ET ASSURER UN CONTACT
ÉLECTRIQUE ADÉQUAT SUR L’ENSEMBLE
DES CONDUCTEURS DE TERRE, CONDUITS
MÉTALLIQUES ET BORNES DE TERRE.
AVERTISSEMENT
WARNING
ADVERTENCIA
NOT FOR USE WITH MEDICAL OR
LIFE-SUPPORT EQUIPMENT
Z-WAVE ENABLED DEVICES SHOULD
NEVER BE USED TO SUPPLY POWER TO
OR CONTROL THE ON/OFF STATUS OF
MEDICAL OR LIFE-SUPPORT EQUIPMENT.
NE PAS UTILISER AVEC
UN ÉQUIPEMENT MÉDICAL
OU DE SURVIE
LES DISPOSITIFS COMPATIBLES
AVEC LA TECHNOLOGIE Z-WAVE NE
DEVRAIENT JAMAIS ÊTRE UTILISÉS
POUR ALIMENTER OU COMMANDER
LA MISE EN MARCHE OU L’ARRÊT DE
L’ÉQUIPEMENT MÉDICAL OU DE SURVIE.
SE PROHÍBE SU EMPLEO EN
EQUIPO MÉDICO O EQUIPO
PARA EL MANTENIMIENTO DE
LAS FUNCIONES VITALES
LOS DISPOSITIVOS Z-WAVE NUNCA
SE DEBEN USAR PARA SUMINISTRAR
ENERGÍA ELÉCTRICA AL EQUIPO MÉDICO
O AL EQUIPO PARA EL MANTENIMIENTO
DE FUNCIONES VITALES, NI PARA
CONTROLAR EL ESTADO DE ENCENDIDO
O APAGADO DE DICHOS EQUIPOS.
1/2in.
3/4in.
Getting to know your new Z-Wave device
• Operation mode switch allows operation
without requiring Z-Wave network
• Remote ON/OFF control via the Z-Wave
controller, on mobile devices
• Manual override ON/OFF control with
the exterior-mounted push button
• Weather-resistant, rainproof housing; suitable
for use outdoors in damp or wet conditions
• Lockable tamper-resistant metal case ensures
secure connection and keeps dirt & debris out
• Energy monitoring capability allows remote monitoring
of watts and kilowatt hours with compatible systems
Tools you will need
1.
1.
A. Indicator Lights
Red light
— indicates smart switch is powered
Green
light
— indicates connected device is turned ON
B. Manual Override Button
Single
press
— turn the connected device(s) ON/OFF
when operation mode switch is set to “Z-Wave
”
C. Operation Mode Switch
ON
— when set to “
” icon, the connected device
has continuous power. Z-Wave control is disabled.
OFF
— when set to “
” icon, the connected
device has no power. Z-Wave control is disabled.
Z-Wave
— when set to “
” icon, Z-Wave
control is enabled. The connected device is
controlled by Z-Wave and the front pannel.
D. Connection Terminal
E. Programming Button
F. S2 Security Label/SmartStart QR Code
2.
2.
Pre-installation
Before installation, follow the instructions below to remove knockouts to route
wiring to connection terminals. Knockouts may be made 1/2in. or 3/4in.
For 1/2in. knockout
1.
Place a small blade screwdriver into inner ring of knockout circle as pictured above.
2.
Tap down with the screwdriver to punch the 1/2in. knockout loose.
For 3/4in. knockout
1.
Create 1/2in. knockouts as instructed.
2.
With pliers, grip outer ring of knockout circle.
3.
Gently twist and pull to remove outer ring and form 3/4in. knockout.
3.
3.
4.
4.
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture
at the service panel. All wiring connections must be made with the POWER
OFF to avoid personal injury and/or damage to the switch. This device
is intended for installation in accordance with the National Electric Code
and local regulations in the United States or the Canadian Electrical Code
and local regulations in Canada. If you are unsure or uncomfortable about
performing this installation consult a qualified electrician.
Choose a suitable mounting location
Before you start, choose a location for mounting the
box with the following considerations in mind:
1.
RF range can be affected by obstructions, metal objects, distance
and weather. Mount unit as close to the Z-Wave controller as possible.
2.
Mount in a location with at least 4in. of space above unit to allow
space for antenna.
3.
Install upright, in vertical orientation.
Mounting the box on drywall
1.
H
old the box in place and use the three holes (highlighted
above) to mark position on the mounting surface.
2.
Drill a 3/16in. hole for the drywall anchors at each
marked location.
3.
Insert an anchor in each hole. Gently tap the open end of
anchor with a hammer until the anchor is flush with the wall.
4.
Align the smart switch with the anchors and secure it with
the supplied screws.
Mounting the box on plywood
1.
Hold the box in place and use the three holes (highlighted above)
to mark position on the mounting surface.
2.
Drill a 3/32in. hole at each marked location.
3.
Mount the box to the surface using the three supplied #10 screws
.
IMPORTANT!
Always close the rainproof door after use.
Antenna setup
1.
Make sure the black antenna wire is routed through the externally
threaded hole on top of the unit.
2.
A weather-resistant, black rubber antenna cover is included in top
of the packaging. Place the antenna cover over the wire and screw
down securely.
Connections
Terminal 1: 240V line 1
Terminal 2: 240V line 2
Terminal 3/5: Jumper connection
between terminals
Terminal 4: Load line 2
Terminal 6: Load line 1
Connections
Terminal 1: 120V neutral/load 2 neutral
Terminal 2/5: 120V line/jumper
Connection between terminals
Terminal 3: Load 1 neutral
Terminal 4: Load 1 line
Terminal 6: Load 2 line
Connections
Terminal 1: 120V neutral
Terminal 2/5: 120V line/jumper
Connection between terminals
Terminal 3: Load 1 & 2 neutral
Terminal 4: Load 1 line
Terminal 6: Load 2 line
5.
5.
240VAC - Single Load Energy Monitored
120VAC - Single Load Energy Monitored
120VAC - Dual Load Load 1 Monitored
1
2
3
4
5
6
Load Line 2
Load Line 1
Jumper
Line 1
Line 2
Green/Bare
Ground
LOAD
1
2
3
4
5
6
Neutral
Neutral
Line
Line
Green/Bare
Ground
LOAD
1
2
3
4
5
6
Neutral
Line
Neutral
Neutral
Line
Jumper
Line
Green/Bare
Ground
LOAD
LOAD
1
2
1
2
3
4
5
6
Neutral
Line
Neutral
Neutral
Line
Jumper
Line
Green/Bare
Ground
Neutral
LOAD
LOAD
1
2
120VAC - Dual Load Total of Both Loads Monitored
For proper wiring connections
1.
Strip 1/2in. of insulation covering wires.
2.
Tighten all screw terminals to 25lbf-in.
Note:
Improper tightening can cause overheating and equipment failure.
Warning!
Turn off power to the switch at the service panel.
Refer to “Warning – Shock Hazard” above.
3.
Open metal enclosure door. Raise plastic guard covering terminals 1-6.
4.
Input voltage connection
a.
Connect 240VAC line 1 (black) to terminal 1.
b.
Connect 240VAC line 2 (black) to terminal 2.
c.
Connect ground wire (green/bare) to ground terminal.
5.
Jumper connection
Connect jumper wire between terminals 3 and 5.
6.
Load connection
a.
Connect load Line 1 (black) to terminal 6.
b.
Connect load Line 2 (black) to terminal 4.
c.
Connect ground wires (green/bare) to ground terminal.
7.
Lower plastic guard covering terminals 1-6. Close metal enclosure door.
8.
Connection check
a.
After 24 hours, disconnect power to module and check the connections.
b.
Open metal enclosure door. Raise plastic guard covering terminals 1-6.
c.
Verify all screws/connections are securely tightened.
9.
Lower plastic guard covering terminals 1-6. Close metal enclosure door.
IMPORTANT: Always close rainproof door after use.
Connections
Terminal 1: 120V neutral
Terminal 2: 120V line
Terminal 3: Load neutral
Terminal 4: Load line
For proper wiring connections
1.
Strip 1/2in. of insulation covering wires.
2.
Tighten all screw terminals to 25lbf-in.
Note:
Improper tightening can cause overheating and equipment failure.
Warning! Turn off power to the switch at the service panel.
Refer to “Warning – Shock Hazard” above.
3.
Open metal enclosure door. Raise plastic guard covering terminals 1-6.
4.
Input voltage connection
a.
Connect 120VAC neutral (white) to terminal 1.
b.
Connect 120VAC line (black) to terminal 2.
c.
Connect ground wire (green/bare) to ground terminal.
5.
Load connection
a.
Connect load neutral (white) to terminal 3.
b.
Connect load line (black) to terminal 4.
c.
Connect ground wires (green/bare) to ground terminal.
6.
Lower plastic guard covering terminals 1-6. Close metal enclosure door.
7.
Connection check
a.
After 24 hours, disconnect power to module and check the connections.
b.
Open metal enclosure door. Raise plastic guard covering terminals 1-6.
c.
Verify all screws/connections are securely tightened.
8.
Lower plastic guard covering terminals 1-6. Close metal enclosure door.
IMPORTANT: Always close rainproof door after use.
Adding your device
1.
Follow the instructions for your Z-Wave certified controller to add a device to the
Z-Wave network.
2.
Once the controller is ready to add your device, press the programming button.
If prompted by the controller to enter the S2 security code, refer to the QR code/
security number on the back of the box or the QR code label on the product. Enter
the 5-digit code.
Note
: Your controller may need to be within 10ft. of the device to be added.
3.
Once your controller has confirmed the device has been added, refresh the Z-Wave
network to optimize performance.
You have complete control to turn your fixture ON/OFF according to groups,
scenes, schedules and interactive automations programmed by your controller.
If your Z-Wave certified controller features remote access, you can control your
fixture from your mobile devices.
To remove and reset your device
1.
Follow the instructions for your Z-Wave certified controller to remove a device from
the Z-Wave network.
2.
Once the controller is ready to remove your device, press the programming button.
6.
6.
A
B
D
C
E
F
Z-WAVE INTEROPERABILITY
This product can be added and operated
in any Z-Wave network with other Z-Wave
certified devices from other manufacturers
and/or other applications. All non-battery
operated nodes within the network will
act as repeaters regardless of vendor
to increase reliability of the network.
• This device supports Association Command Class (3 Groups)
• Association Group 1 supports Lifeline, Basic Report
• Association Group 2 supports Basic Set and is controlled with the local load
• Association Group 3 supports Basic Set and is controlled by pressing the
Programming button
• Each Association Group supports 5 total nodes
Example:
To return your device to factory defaults
14285
ZW4007
READ IT
OR
WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit byjasco.com/14285i
Direct Wire
Indoor/Outdoor
Smart Switch
À Raccordement Direct
Intérieur/Extérieur
Interrupteur Intelligent
Cable Directo
Para Interiores/Exteriores
Interruptor Inteligente
Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils exempts
de licence d’Industrie Canada. Son utilisation est sujette aux deux conditions suivantes : (1) cet
appareil ne doit pas occasionner de brouillage préjudiciable et (2) cet appareil doit accepter toutes
les interférences reçues, notamment les interférences qui peuvent provoquer un fonctionnement non
désiré.
NOTE DE LA FCC :
Le fabricant n’est pas responsable des interférences sur les fréquences
radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées de ce
matériel. De telles modifications peuvent annuler le droit de l’utilisateur à utiliser cet appareil.
REMARQUE :
Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont été
définies afin de fournir une protection raisonnable contre le brouillage préjudiciable en milieu
résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence radio et, s’il n’est pas
installé et utilisé conformément aux instructions, il peut provoquer un brouillage préjudiciable aux
communications radio. Il n’existe toutefois aucune garantie que des interférences ne se produiront
pas au sein d’une installation donnée. Si cet appareil occasionne un brouillage préjudiciable à la
réception radiophonique ou télévisuelle, il suffit d’allumer et d’éteindre l’appareil pour déterminer sa
responsabilité. Nous encourageons l’utilisateur à essayer de corriger ces interférences en appliquant
une ou plusieurs des mesures suivantes :
— Réorienter ou déplacer l’antenne de réception.
— Augmenter la distance entre l’appareil et le récepteur.
— Brancher l’appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC concernant
l’exposition aux RF, aucune modification apportée à l’antenne ou au dispositif n’est autorisée. Toute
modification apportée à l’antenne ou au dispositif pourrait faire en sorte que le dispositif dépasse les
exigences d’exposition aux RF et pourrait annuler le droit de l’utilisateur à utiliser ce dispositif.
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE:
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Important note: To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could result in the
device exceeding the RF exposure requirements and void user’s authority to operate the device.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con las
especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria de Canadá aplicables
a aparatos exentos de licencia. El funcionamiento está sujeto a las siguientes dos condiciones: (1)
este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo debe aceptar
toda interferencia que reciba, incluso la que pudiera causar un funcionamiento no deseado.
NOTA DE LA FCC:
El fabricante no se hace responsable de ninguna interferencia de radio
o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas
modificaciones podrían anular la autoridad del usuario para utilizar el equipo.
NOTA:
Este equipo ha sido probado y cumple con los límites para aparatos digitales de Clase B,
de conformidad con el apartado 15 de las normas de la FCC. Estos límites están diseñados para
proveer protección razonable contra interferencias perjudiciales en una instalación residencial. Este
equipo genera, usa y puede irradiar energía de radiofrecuencias y, si no se instala y usa según las
instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No obstante, no
hay garantías de que no ocurrirá interferencia en una instalación en particular. Si este equipo provoca
interferencia perjudicial a la recepción de radio o televisión, lo que puede determinarse encendiendo
y apagando el equipo, se recomienda que el usuario intente corregir la
interferencia por medio de la implementación de una o más de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente
del circuito al que está conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante:
Para cumplir con los requisitos de cumplimiento de exposición de
radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier
cambio a la antena o dispositivo podría hacer que el dispositivo supere los requerimientos de
exposición de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo.
Responsible Party - US Contact Information | Parte responsable - Información de contacto de los
Estados Unidos | Partie responsable - Coordonnées des États-Unis
ZW4007:
FCC ID — U2ZZW4007 | IC: 6924A-ZW4007
Jasco Products Company | Model: ZW4007/14285
10 E. Memorial Rd., Oklahoma City, OK 73114 | 1-800-654-8483
CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks
of their respective owners.
Tous les noms de marque illustrés sont des marques
de commerce de leurs propriétaires respectifs.
Todas las marcas que aparecen aquí son marcas
registradas de sus respectivos dueños.
MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO EN CHINA
JASCO PRODUCTS COMPANY LLC,
10 E. MEMORIAL RD., OKLAHOMA CITY, OK 73114.
©JASCO 2020 | 14285 | ZW4007 | 12/22/20 v3
FCC/IC
DO NOT RETURN THIS
PRODUCT TO THE STORE
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
STOP
If you have any problems or questions, contact our U.S.-based Consumer Care at
1-800-654-8483, option 1, Monday–Friday, 7AM–8PM Central Time.
For the most up-to-date product support, accessories, electronic (PDF)
format manuals and more, visit www.byjasco.com/support.
• No user-serviceable parts in this unit.
Si vous avez des problèmes ou des questions, veuillez communiquer avec notre
service à la clientèle aux États-Unis au 1-800-654-8483, option 1, du lundi au
vendredi, de 7 h à 20 h (HNC).
Pour le soutien relatif aux produits le plus à jour, les accessoires, les manuels en
format électronique (PDF) et plus encore, visitez le site www.byjasco.com/support.
• Aucune des pièces de ce dispositif ne peut être réparée par l’utilisateur.
Si tiene problemas o dudas, comuníquese con nuestro Centro de
atención al cliente con sede en EE. UU. al 1-800-654-8483, opción 1 de
lunes a viernes, de 7 a.m. a 8 p.m., hora estándar del centro (CST).
Para recibir el soporte técnico más actualizado sobre productos, accesorios,
manuales en formato digital (PDF), entre otros, visite www.byjasco.com/support.
• Esta unidad no contiene piezas que el usuario pueda reparar.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from
the original date of consumer purchase. This warranty is limited to the repair or replacement of this
product only and does not extend to consequential or incidental damage to other products that may be
used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states
do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of
incidental or consequential damage, so the above limitations may not apply to you. This warranty gives
you specific rights, and you may also have other rights which vary from state to state. Please contact our
U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM – 8PM, M-F, Central Time or
www.byjasco.com if the unit should prove defective within the warranty period.
GARANTIE
Jasco Products Company garantit que ce produit est exempt de tout défaut de fabrication pendant une
durée à cinq ans compter de la date de l'achat original par l'acheteur. Cette garantie se limite
exclusivement à la réparation ou au remplacement de ce produit et n'est pas applicable aux dommages
indirects ou accessoires survenus sur d'autres produits utilisés avec ce produit. Cette garantie se substitue
à toute autre garantie expresse ou implicite. Certains États ne permettent pas de restrictions quant à la
durée d'une garantie implicite ou permettent l'exclusion ou la limitation des dommages indirects et
accessoires; il se peut, par conséquent, que cette garantie ne s'applique pas dans votre cas. Cette garantie
vous confère des droits juridiques précis; vous pouvez jouir d'autres droits qui peuvent varier d'un État à
l'autre. Veuillez communiquer avec notre service à la clientèle aux États-Unis au 1-800-654-8483 (option
1) entre 7 h et 20 h, heure du Centre ou par l’intermédiaire de notre site web www.byjasco.com si l’appareil
s’avère défaillant au cours de la période de garantie.
GARANTÍA
Jasco Products Company garantiza que este producto no tendrá defectos de fabricación por un cinco
años a partir de la fecha de compr a del consumidor original. Esta garantía se limita a la reparación o
reposición de este producto y no cubre daños indirectos o incidentales a otros productos que se pudieran
utilizar con este producto. Esta garantía reemplaza cualquier otra garantía explícita o implícita. Algunos
estados no permiten la aplicación de limitaciones respecto de la duración de una garantía implícita o
permiten la exclusión o limitación de la cláusula sobre daños indirectos o incidentales, por este motivo las
limitaciones arriba mencionadas pueden no aplicarse en su caso. Esta garantía le otorga derechos
específicos y es posible que tenga otros derechos que pueden variar según el estado en el que vive. Por
favor, comuníquese con nuestro Centro de atención al cliente con sede en EE. UU. al 1-800-654-8483
(opción 1) entre 7 y 20 h, Hora del Centro, o a través de nuestro sitio de internet www.byjasco.com.
Jasco Products Company LLC, Building B
10 E. Memorial Rd. Oklahoma City, OK 73114.
In-Wall
Smart Dimmers
Plug-in
Smart Dimmers
In-Wall
Add-on Switches
Purchase additional items at
EZzwave.com or visit your local retailer.
In-Wall Motion
Switch or Dimmer
Plug-in
Smart Switches
In-Wall
Smart Switches
Enbrighten
Smart LED Bulb
In-Wall
Smart Fan Control
Hinge Pin
Smart Door Sensor
Portable
Smart Multi
Sensor
In-Wall
Tamper-Resistant
Smart Outlet
Plug-in
Outdoor Smart
Switch
DSK/PIN CODE
DSK :
XXXXX
-25651-22671
-26939-47599
-19612-25872
-47752
NOTE
:
SmartStart enabled products can be added into a Z-Wave network by scanning the
QR code on the product with a controller providing SmartStart inclusion. No further action is
required and the SmartStart product will be added automatically within 10 minutes of being
switched on in the network vicinity.
1.
Place device into ON mode (upper position of operating mode switch)
2.
Press and hold the programming button.
3.
While holding programming button, place device into OFF mode (middle position
of operating mode switch).
4.
While holding programming button, place device back into ON mode (upper
position of operating mode switch).
5.
After three seconds, release programming button. Green LED will flash five times
when completed.
Note: This should only be used in the event your network’s primary controller is
missing or otherwise inoperable.
