background image

YO Analog

User guide

v2.0

page 9/15

Quick start guide

Required equipment/software:

PC with Bluetooth adapter (USB dongle or built-in),

power supply 6 - 30 V DC, 5 - 21 V AC,

Yosensi CLI tool.

NOTE

Yosensi CLI tool works only with YO Analog default Yosensi firmware.
For official firmware updates, contact us on [email protected]
.

Node configuration

Connect to the device following these instructions:

1. Read the macBLE address from the sticker on the device. Alternatively, you can identify

the device by RSSI parameter (which correlates with distance between transmitter and
receiver).

Figure 5

Device information sticker/nameplate example.

2. Make sure you have your Bluetooth LE adapter turned on and working properly.
3. Download and run the CLI tool in the terminal/console application.
4. Connect power supply pins (regardless of polarity) of the YO Analog device. See Quick

Installation Guide for step by step instructions.

5. Run

yosensi-cli-tool_vX.X.X_WIN.exe list

to scan for Bluetooth devices. You can

see all commands by typing

yosensi-cli-tool_vX.X.X_WIN.exe --help

or add

-h

to

your current command to see all needed parameters.

6. If you find your MAC address in the

list

command results, you can connect and

reconfigure the device by using one of the available commands. You should use

change_dev_params

subcommand to change device settings. Additional information,

including the commands supported by the CLI, are available at

https://yosensi.io/support

.

REV 2.0.0

www.yo

sensi

.

io

Содержание YO Analog
















Отзывы: