York YHAU-CGH страница 153 Скачать руководство пользователя | Manualshive

Страница: 153 / 182

background image

FORM 155.32-ICOM2.EN.UL

SECTION 7 – MAINTENANCE

ISSUE DATE:1/10/2018

JOHNSON CONTROLS

153

STORAGE METHOD OF THE COOLING WATER DURING HEATING
OPERATION PERIOD

Do NOT operate the cooling water pump during operation in heating mode, simultaneous
heating and residential hot water supply mode, and residential hot water only (sole) supply
mode.

Treat the cooling water in the absorber and condenser tubes during the heating operation
using one of the following two methods.

Wet Storage

This method of storage leaves water in the tubes. It is applicable to indoor installations.

Condition around the chiller-heater:

1. During the heating operation period, there is no concern about the cooling water freez-

ing. (In case there is concern of freezing, apply insulation material to the cooling water
piping.)

2. The cooling tower is installed at the high level (height) of the chiller-heater to prevent

water from flowing into the cooling tower.

3. Lining pipe is not used for the cooling water piping system. If you use the lining pipe,

use a heat -resistant lining pipe.

CAUTION: To avoid risk of corrosion of the heat transfer tubes, do NOT leave any poor
quality cooling water in the absorber and condenser tubes.

DANGER: Cooling water temperature can rise up to approximately

176°F (80°C).

due

to the residual heat during heating operation. Be careful of burns when handling the
water drain valves or other hot components of the machine.

NOTE: With increased cooling water temperature, the volume of the cooling water ex-
pands. Therefore, be sure to slightly open the valve at the cooling water outlet side of
the chiller-heater.

«
...
151
152
153
154
155
...
»

Содержание YHAU-CGH























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YHAU-CGH

Бренд: Yard Machines Страницы: 20

Бренд: MTA Страницы: 68

Бренд: Poulan Pro Страницы: 40

Millennium YCAR 0100SC

Бренд: York Страницы: 24

Бренд: Cole Parmer Страницы: 48

EUWL KZW1 Series

Бренд: Daikin Страницы: 140

Бренд: Ozito Страницы: 6

ZANUSSI Easychill 110046

Бренд: Zanussi Страницы: 3

ZANUSSI easyChill BCFW061

Бренд: Zanussi Страницы: 4

ZANUSSI easyChill 110043

Бренд: Zanussi Страницы: 3

ZANUSSI easyChill 110022

Бренд: Zanussi Страницы: 4

Бренд: F.F. Group Страницы: 84

Blue Chilled 40 693

Бренд: Grohe Страницы: 90

PRO-DIALOG PLUS 30RW

Бренд: Carrier Страницы: 36

GEMINI 09DPM035

Бренд: Carrier Страницы: 40

Hyperchill ICE015

Бренд: Parker Hiross Страницы: 36

Бренд: Stiga Страницы: 14

Бренд: Johnson Controls Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды