York YHAU-CGH Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 182

York YHAU-CGH Скачать руководство пользователя страница 95

FORM 155.32-ICOM2.EN.UL

SECTION 6 – OPERATION

ISSUE DATE:1/10/2018

JOHNSON CONTROLS

95

The Operation Hours section shows the following:

•

Operation:

how long the chiller-heater has been running.

•

Cooling:

how long the chiller-heater has been running in cooling mode

•

Heating:

how long the chiller-heater has been running in heating mode

•

Solution Pump:

how long the solution pump has been running.

•

Refrige. Pump:

how long the refrigerant pump has been running.

•

Burner:

how long the burner for the chiller-heater has been running

The frequency of failures, alarms, and purges is shown in the Frequency section:

•

Operation:

displays how many times the chiller-heater has started using the

OPER.

button or a remote start signal.

•

Cooling:

displays how many times the chiller-heater has started using the

OPER.

but-

ton or a remote start signal in cooling mode

•

Heating:

displays how many times the chiller-heater has started using the

OPER.

but-

ton or a remote start signal in heating mode

•

Start:

displays how many times the burner has started.

•

Failure:

displays how many times the system has experienced a failure.

•

Alarm:

displays how many times an alarm has been activated.

•

Auto Purge:

displays how many times the automatic purge system has started.

To move to the Trend screen, press the

Trend

button at the upper right of the screen.

The History Menu section on the right side of the screen gives you access to the operation
history, Alarm History and to the Failure History screens. It contains four buttons:

•

Hourly Operation:

move to the Hourly Operation History screen

•

Minutely Operation:

move to the Minutely Operation History screen

•

Failure History:

move to the Failure History screen

•

Alarm History:

move to the Alarm History screen

The Maintenance Information section contains three buttons. They provide information on
how long it has been since maintenance was done. They also indicate if maintenance is
required. The buttons are:

•

Solution Analysis or Ctrl. Pn. Parts Replace:

Information on the last time solution

analysis was performed or information about parts of the control panel that need main-
tenance.

•

Solution Pump Overhaul or Ref. Pump Overhaul:

Information on the last time the

solution pump or the refrigerant pump were overhauled.

•

Combustion Check or Burner Parts Replace:

Information on the last time a com-

bustion check was done or how long it has been since any of the burner parts were
replaced.

If the lettering on any of the buttons is red, immediate attention is needed.

«
...
93
94
95
96
97
...
»

Содержание YHAU-CGH























































































































































































Отзывы:

Нет отзывов