York YHAU-CGH страница 83 Скачать руководство пользователя | Manualshive

Страница: 83 / 182

background image

FORM 155.32-ICOM2.EN.UL

SECTION 5 - COMMISSIONING

ISSUE DATE:1/10/2018

JOHNSON CONTROLS

83

SECTION 5 - COMMISSIONING

GENERAL GUIDELINES FOR USE

Before Operation

Charge the solution and the refrigerant water if the solution and refrigerant water is in the
barrels during the delivery.

During commissioning, check the motor’s rotating direction of the solution pump, refrigerant
pump, and purge pump.

The rotation direction can be tested by using a rotation detector (Bell and Gosset or WILO
DKG). If a rotation detector is not available, use the procedure shown below:

1. Remove the plugs at the solution and refrigerant sampling valves.

2. Make sure the valves are completely closed.

3. Confirm that the absorber and refrigerant tank contain enough solution and refriger-

ant.

4. Connect a compound gauge (NPT 1/2 of an inch) to the sampling valve with Teflon

tape.

5. Operate the pump.

6. Open the valve.

7. Read and record the delivery pressure of the solution pump and the refrigerant pump.

8. Close the valve.

9. Check the pressure readings, see

Table 29 on page 84

to see if your pump rotation

is in the right direction. The correct direction shows a higher discharge pressure.

10. Remove the compound gauge.

11. Put the plugs back on the valves.

12. Clean the gauge with water.

13. For refrigerant, confirm the correct rotation by looking at the refrigerant spray through

the sight glass.

NOTE: The flow of fluid cannot be seen because the solution and refrigerant pumps are
hermetically sealed.

CAUTION: Do not run the solution pump without solution. Do not run the refrigerant
pump without refrigerant water .

NOTE: The gauge scale must be -760 mm Hg. to 2 Kg. / cm2g, or -30 inches Hg. to 30
psig. To prevent corrosion of the gauge, clean it thoroughly, and check it for leaks after
each use.

NOTE: The delivery pressure reflects the high vacuum condition of the machine. If the
inside pressure is atmospheric, add 1.0 kg / cm (14.3 psig) to the standard value found
in

Table 29 on page 76.

«
...
81
82
83
84
85
...
»

Содержание YHAU-CGH























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YHAU-CGH

Бренд: Daikin Страницы: 88

Бренд: Nakayama Страницы: 17

Бренд: Cole Parmer Страницы: 48

Бренд: Whirlpool Страницы: 56

Бренд: Cobra Страницы: 19

Бренд: Troy-Bilt Страницы: 64

634B-Super Bronco

Бренд: Troy-Bilt Страницы: 32

Бренд: Troy-Bilt Страницы: 20

Бренд: EarthWise Страницы: 42

Бренд: Cavecool Страницы: 23

Бренд: Arktic Страницы: 56

Бренд: Weed Eater Страницы: 20

Бренд: Weed Eater Страницы: 28

Бренд: Weed Eater Страницы: 24

Бренд: Weed Eater Страницы: 28

Бренд: Nakayama Страницы: 11

H50 SMART Series

Бренд: Labtech Страницы: 32

Бренд: York Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды