York YHAU-CGH страница 164 Скачать руководство пользователя | Manualshive

Страница: 164 / 182

background image

SECTION 8 – TROUBLESHOOTING

FORM 155.32-ICOM2.EN.UL

ISSUE DATE:1/10/2018

164

JOHNSON CONTROLS

Table 50 -

CPU Abnormal

In the case of chilled/hot water suspension, the absorption chiller-heater does not dilute the
solution, but stops immediately. If the absorption chiller-heater is left in this current state,
the solution in it may crystallize within 4-5 hours. To prevent this, dilute the solution.

Table 51 -

Chilled or Hot Water Suspension

If the chiller-heater has a pump problem, it does not perform the diluting operation but stops
immediately. If left in this condition, the solution in the pump may crystallize within 4-5
hours. To prevent this, contact your local Johnson Controls Service Office immediately.

Table 52 -

Pump(s) Overloaded or Overheated

ITEM

CAUSE

COUNTERMEASURE

1

Control board malfunction

Contact your local Johnson Controls Service Office.

NOTE: The time required for refinement of the refrigerant depends on the current
load condition. Constantly check the liquid level in the refrigerant tank while the
refrigerant is refined. If the refrigerant liquid level appears in the level gauge of the
refrigerant tank, close the valve immediately and completely.

ITEM

CAUSE

COUNTERMEASURE

1

Chilled/hot water pump has a
problem.

Check the chilled/hot water pump for a problem.

2

Chilled/hot water flow rate is low.

• Check to see if the chilled/hot flow- rate is below the

setpoint of the water suspension switch. If it is low,
check the flow controller, check the strainer for
clogging.

• Check the opening ratio of the flow control valve.

3

Pressure transfer pipe of water
suspension switch is clogged.

Contact your local Johnson Controls Service Office.

4

Water suspension switch is broken.

ITEM

CAUSE

COUNTERMEASURE

1

Bearings of the pump are worn or clogged.

Contact your local Johnson Controls
Service Office.

2

Pump is damaged by cavitation caused by low
liquid level.

3

Thermal switch is not set properly.

4

Internal cycle control valve is not set properly.

5

Filter in the pump is clogged.

6

Solution is crystallized.

7

Circuit breaker has tripped.

«
...
162
163
164
165
166
...
»

Содержание YHAU-CGH























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YHAU-CGH

Millenium YK D Series

Бренд: York Страницы: 28

Бренд: McQuay Страницы: 189

Бренд: Arctica Страницы: 15

Бренд: LG Страницы: 107

Бренд: Lava Страницы: 76

Бренд: Polar Refrigeration Страницы: 40

Бренд: Draper Страницы: 13

Бренд: Draper Страницы: 24

Бренд: Hansa Страницы: 28

Бренд: Agrisem Страницы: 130

Бренд: Portland Страницы: 12

Бренд: Echo Страницы: 1

Бренд: Perlick Страницы: 12

Бренд: Texas Equipment Страницы: 27

Agri-Fab 45-0578

Бренд: SpeedEPart Страницы: 24

Бренд: Yard Machines Страницы: 64

Бренд: Valex Страницы: 16

Бренд: Ozito Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды