manualshive.com logo in svg

York YHAU-CGH, Установка, эксплуатация и обслуживание, Страница: 163 / 182

Поделиться
Скачать
York YHAU-CGH Скачать руководство пользователя страница 163

FORM 155.32-ICOM2.EN.UL

SECTION 8 – TROUBLESHOOTING

ISSUE DATE:1/10/2018

JOHNSON CONTROLS

163

Table 46 - 

Chilled or Hot Water Time Out or Cooling Water Time Out

Table 47 - 

Pump Interlocks

Table 48 - 

Low Cooling Water Inlet Temperature

Table 49 - 

Abnormal Control Sensor

If these problems occur, the absorption chiller-heater performs the dilution operation and
then stops. Go to the Control Center immediately and confirm that the dilution took place. If
the dilution operation did not run, dilute the solution.

ITEM

CAUSE

COUNTERMEASURE

1

Pump abnormal

Check the water pump.

2

Insufficient water flow

• Check the water line.
• Check the water flow.

3

Water suspension relay abnormal

• Check the water suspension relay.
• Check to see if the pipe is clogged.

4

Water pump interlock abnormal

Check the water pump.

ITEM

CAUSE

COUNTERMEASURE

1

Water pump interlock was not established

Check the water pump interlock.

ITEM

CAUSE

COUNTERMEASURE

1

Cooling water inlet 
temperature 
control system is 
abnormal

Check the cooling water inlet temperature control system. If this problem 
occurs, the absorption chiller-heater performs the dilution operation 
automatically and then stops. Go to the Control Center immediately to 
confirm that the dilution took place. If it did not, you will need to perform 
the dilution process, see 

Location of Manual Valve in Purging System 

120-300EX(H/S) on page 124

.

NOTE: The time required for refinement of the refrigerant depends on
the current load condition. Constantly check the liquid level in the re-
frigerant tank while the refrigerant is refined. If the refrigerant liquid
level appears in the level gauge of the refrigerant tank, close the valve
immediately and fully. If the refrigerant liquid level appears in the lev-
el gauge of the refrigerant tank, completely close the valve immedi-
ately.

ITEM

CAUSE

COUNTERMEASURE

1

Contact failure

Tighten terminal in control panel. 

2

Sensor abnormal or disconnected

Contact your local Johnson Controls Service 
Office.

3

Inductive noise

Содержание YHAU-CGH























































































































































































Отзывы:

Нет отзывов