York YHAU-CGH Скачать руководство пользователя страница 122

Страница: 122 / 182

SECTION 7 – MAINTENANCE

FORM 155.32-ICOM2.EN.UL

ISSUE DATE:1/10/2018

122

JOHNSON CONTROLS

PUMP SHUT OFF VALVES

The chiller-heater is equipped with the pump shut off valves. See

Figure 59 on page 124

and

Figure 61 on page 126

. They are used for inspection of the pumps.

If the absorption chiller-heater is operated with incorrect valve settings, the pump may be
damaged. Do NOT tamper with the valves.

AIR PURGE VALVES AND DRAIN VALVES

The chiller-heater is equipped with air purge valves and drain valves for chilled/hot water
and cooling water. They are used to drain the chilled/hot water, and cooling water. They
also purge air when water is supplied.

PURGE VALVES

The chiller-heater is equipped with the purging valves. See

Figure 63 on page 130

Figure

64 on page 131

Figure 65 on page 132

, a nd

Figure 66 on page 133

For operation of those

valves, see

Purge Procedure on page 123

START THE CHILLER-HEATER AFTER IT HAS BEEN STOPPED FOR
A LONG PERIOD

When starting the chiller-heater after stopping it for a long period, check it according to the
following procedure.

Checks Before Operation Starts

1. Check the insulation of the Control Center and electric system.

2. Check the operation of the Control Center and safety devices.

3. Check that the refrigerant blow valve V8 is closed.

4. Check the vacuum level in the machine. Use pressure gauge of the high-temperature

generator.

5. Check the fuel gas supply.

6. Press the Refrigerant Pump

Stop

button on the Setting screen.

If the checks show no problems, start the chiller-heater.

Checks After Operation Starts

1. 10-15 minutes after the chiller-heater and the solution pump start, check the level

gauge of the refrigerant tank.

2. If the refrigerant level is within the level gauge, press the Refrigerant Pump

Auto

but-

ton.

3. Observe the operation for a while. Check that the refrigerant liquid level does not

drop.

4. Use the procedure shown in

Purge Procedure on page 123

to purge air from the low

pressure side (absorber).

NOTE: It should be less than -0.1 MPaG.

NOTE: Only deionized water may be used as the refrigerant in the chiller-heater.

Содержание YHAU-CGH























































































































































































Результаты поиска

Содержание YHAU-CGH

Отзывы:

York YHAU-CGH, Установка, эксплуатация и обслуживание, Страница: 122 / 182

Результаты поиска

Содержание YHAU-CGH

Отзывы: