York YCIV Series Скачать руководство пользователя страница 258

Страница: 258 / 326

JOHNSON CONTROLS

258

FORM 201.23-NM2

ISSUE DATE: 09/25/2020

SECTION 8 - MICROPANEL

LD10605

SETPOINTS

KEY

SETPOINTS KEY

Setpoints Key Operation

Cooling setpoints and ranges may be programmed by

pressing the SETPOINTS key. The first setpoint en-

try screen will be displayed as shown below. The first

line of the display will show the chiller default (DEF),

minimum acceptable value (LO) and maximum ac-

ceptable value (HI). The second line shows the actual

programmed value.

Table 20 on page 259

also shows

the allowable ranges for the cooling setpoints and Con-

trol Ranges. Note that the Imperial units are exact val-

ues while the Metric units are only approximate.

SETPOINTS ◄DEF XXXXX LO XXXXX HI XXXXX

LOCAL COOLING SETPOINT = XXX.X °F

Pressing the SETPOINTS key a second time or the ▼

(ARROW) key will display the leaving chilled liquid

Control Range, default, and low/high limits.

SETPOINTS ◄DEF XXXXX LO XXXXX HI XXXXX

LOCAL CONTROL RANGE = +/- X.X °F

Pressing the SETPOINTS key or the ▼ (

ARROW) key

a third time will display the remote setpoint and cool-

ing range. This display automatically updates about

every 2 seconds. This remote setpoint message is show

below:

SETPOINTS REMOTE SETPOINT = XXX.X °F
REMOTE CONTROL RANGE = +/- X.X °F

If there is no remote setpoint being utilized, the remote

setpoint value will be displayed as XXXXXX and the

remote Control Range will display XXX.
Pressing the SETPOINTS key or the Arrow key a

fourth time will bring up a screen that allows the Maxi-

mum Remote Temperature Reset to be programmed.

This message is show below:

SETPOINTS ◄DEF XXXXX LO XXXXX HI XXXXX

MAXIMUM REMOTE TEMP RESET = XXX.X °F

Содержание YCIV Series







































































































































































































































































































































Результаты поиска

Содержание YCIV Series

Отзывы:

Похожие инструкции для YCIV Series

Бренды по названию

Популярные бренды

York YCIV Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание YCIV Series

Отзывы:

Похожие инструкции для YCIV Series

Бренды по названию

Популярные бренды