York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 68 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays the capacity control setpoints.

A Service Level password is required to access this

screen.

DISPLAY ONLY

All other parameters are view only and may be request-

ed by Product Technical Support or Chiller Engineer-

ing when assisting in troubleshooting.

PROGRAMMABLE (REQUIRES SERVICE

PASSWORD)
Change Setpoints

Pressing this button highlights the first of the change-

able parameters, LCHLT Setpoint Ramp Rate.

LCHLT Setpoint Ramp Rate

When the chiller is not running, the Active Setpoint

is set to Entering Chilled Liquid Temperature minus a

programmable offset (default 5°F), but not adjusted to

less than the programmed LCHLT setpoint. When the

compressor motor starts, the Active LCHLT Setpoint

is ramped from this value to the programmed LCHLT

Setpoint at the programmable LCHLT Setpoint Ramp

Rate (default 0.1°F/second). This keeps the chiller

from undershooting setpoint excessively during pull-

down. Any time the programmed setpoint is changed

during operation, the active setpoint is ramped to the

new value at this rate. (Adjustable 0.1°F/second to

2.0°F/second, Default 0.1°F/second)

LCHLT Setpoint Start Offset

The LCHLT setpoint offset above the Active setpoint.

(Adjustable 0.0°F to 10.0°F, Default 5.0°F)

Lead PRV Start Position

The desired start position of the Lead compressor PRV.

(Adjustable 0% to 100%, Default 0%)

Gear Ratio Override

Allows the technician to add a buffer above the operat-

ing surge plane by adjusting this parameter. (Adjust-

able 0.0000 to 7.0000, Default 0.0000)

NAVIGATION
Home

Navigates to the Home screen.

Capacity Control

Returns to the Capacity Control screen.

Anti-Surge Tuning

Navigates to the Anti-Surge Tuning screen.

CAPACITY CONTROL SETPOINTS SCREEN

FIGURE 21 -

CAPACITY CONTROL SETPOINTS SCREEN

LD27860

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды