York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 46 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays a cutaway view of the chiller com-

pressor, revealing the proximity probe sensor and pro-

vides the capability of calibrating the proximity probe

sensor. The appearance of this screen is the same for

compressor #1 and compressor #2.

Requires a login access level of

SERVICE.

DISPLAY ONLY
High Speed Thrust Bearing Proximity

Position

Displays the distance between the high-speed thrust

collar and the proximity probe that is used to measure

the position.

High Speed Thrust Bearing Proximity

Reference Position

Displays the presently defined offset reference posi-

tion. This value is defined at the conclusion of a cali-

bration sequence.

Oil Pressure

Displays the pressure differential between the pump oil

pressure transducer (compressor bearing input) and the

sump oil pressure transducer. If either of the transduc-

ers used to calculate this differential is out of range, the

display field will show XX.X.

Calibration in Progress (LED)

Indicates that the calibration sequence is in progress.

Calibration Messages

These are text messages which step the user through

the calibration process and indicate its success or fail-

ure.

PROGRAMMABLE
Enter Reference

Allows the Service Technician to enter a previously re-

corded reference when replacing a microboard.

Start Calibration

This starts the calibration procedure. This key is hid-

den after calibration has started.

PROXIMITY PROBE CALIBRATION SCREEN

LD27850

FIGURE 11 -

PROXIMITY PROBE CALIBRATION SCREEN

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды