York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 35 / 160

JOHNSON CONTROLS

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

This screen displays a cutaway view of the chiller

evaporator. All setpoints relating to the evaporator side

of the chiller are maintained on this screen. Animation

of the evaporation process indicates whether the chiller

is presently in a

RUN

condition. Animation of the liq-

uid flow indicates chilled liquid flow.

DISPLAY ONLY
Leaving Chilled Liquid Temperature

Displays the temperature of the liquid as it leaves the

evaporator.

Entering Chilled Liquid Temperature

Displays the temperature of the liquid as it enters the

evaporator.

Evaporator Small Temp Difference

Displays the difference between the Leaving Chilled

Liquid temperature and the Evaporator Refrigerant

temperature. The Evaporator Refrigerant temperature

is measured by the Refrigerant Temperature sensor in-

put if the sensor is present, otherwise it is calculated

from the Evaporator Saturation temperature.

Evaporator Pressure

Displays the present refrigerant pressure in the

evaporator.

Evaporator Saturation Temperature

Displays the present saturation temperature in the

evaporator.

Evaporator Refrigerant Temperature

Displays the temperature of the refrigerant in the evap-

orator, if the sensor is present.

Chilled Liquid Flow Switch (Open / Closed)

Displays whether the liquid flow is present in the evap-

orator.

Chilled Liquid Pump

Displays the command presently sent by the control

center to the Chilled Liquid Pump (RUN or STOP).

Leaving Chilled Liquid Temperature Setpoints

Setpoint

Displays the present setpoint to which the chiller is op-

erating, whether controlled locally or remotely.

Shutdown

Displays the Leaving Chilled Liquid Temperature at

which the chiller will shut down to avoid over-cooling

the building. By default this value is 4°F below the

Leaving Chilled Liquid Setpoint, but is adjustable.

EVAPORATOR SCREEN

LD27845

FIGURE 6 -

EVAPORATOR SCREEN

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды